2017 Ram 1500 Key Replacement

2017 1500 key specs

From 2013 the Ram 1500 came two ways. Most trucks kept a Fobik that plugs into the dash, now carrying FCC ID GQ4-53T, with three to five buttons depending on remote start and air suspension. Trucks with Keyless Enter 'n Go have a start button and a proximity fob, FCC ID GQ4-54T, that stays in your pocket. Both hide a mechanical emergency key for the doors. Button layouts vary by trim and options, so a replacement should match yours, or the air suspension or remote start button will do nothing.

What's specific to the 2017 1500

The 2017 Ram 1500 is the fifth of 6 model years in the 1500 DS (4th generation, 2013 update) (2013–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 9 years old, a 2017 Ram 1500 has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2017 Ram 1500

• Remote head key. Remote-head keys look similar across many vehicles, but the electronics inside are not interchangeable. Getting the right one for a Ram 1500 means matching the FCC ID and part number printed on the back or inside the case, the operating frequency, which is commonly 315 MHz on US-market cars, the transponder type, and the button layout. A trim with remote start or a power liftgate may use a four- or five-button version where a base trim uses three. We check those details against your VIN and your existing key, if you have one, before cutting the blade. A wrong match can look perfect and still refuse to program.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Ram 1500 DS (4th generation, 2013 update), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Ram immobilizer works on the 1500

• The 2013 update introduced available four-corner air suspension, which is why some fobs from these years carry a suspension button.
• GQ4-53T Fobiks are not interchangeable with the IYZ-C01C fobs used on 2011-2012 trucks.
• The FCC ID on the back, GQ4-53T or GQ4-54T, tells you which of the two systems your truck has.

Programming a 2017 1500 key

Both fob types are added through the OBD-II port with the vehicle PIN, which professional tools can read on most of these trucks. A Fobik is learned by the ignition node and a proximity fob by the keyless ignition system, but the procedure is similar and the remote buttons are paired at the same time. Builds from the end of this span may have a security gateway module, which we get past with a bypass cable or an authenticated tool. All-keys-lost is a normal on-site job for these trucks.

Almost every Ram key job runs through the immobilizer PIN. On Fobik-era trucks and vans, professional tools can usually read it through the OBD-II port and add a fob in one session, which also pairs the lock, unlock and remote start buttons. Newer Rams add a security gateway module that blocks key programming at the diagnostic port until the tool is authenticated online or connected behind the gateway with a bypass cable. The 2019-and-later smart keys are learned by the radio-frequency hub, and the replacement has to match the FCC ID and part-number family of your original, which differ between the 1500 and the Heavy Duty trucks. The Fiat-derived ProMaster and ProMaster City flip keys need specialist equipment, because the remote's own memory has to be written before the van will learn it. Ram fobs are also not plug-and-play from an online marketplace: a used fob only programs after it has been unlocked or re-flashed.

Lost every key to your 1500?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2017 Ram 1500 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

1500 key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your 1500 uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Ram 1500 keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 1500, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a 1500 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Ram 1500 is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2017 Ram 1500 key?

Don't wait until the last key disappears. If your Ram 1500 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.