2013 Nissan Quest Key Replacement

2013 Quest key specs

The last Quest, built in Japan by Nissan Shatai, uses an Intelligent Key with push-button start. Its fob adds buttons for the power sliding doors and liftgate on equipped vans; catalogs list a five-button version under FCC ID CWTWB1U818 and a six-button version under CWTWB1U789. A metal emergency key is stored inside the fob for the driver's door. Retail sales ended with the 2016 model year, and a short 2017 run went to fleet buyers with the same key system.

What's specific to the 2013 Quest

The 2013 Nissan Quest is the third of 7 model years in the Quest RE52 (fourth generation) (2011–2017), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 13 years old, a 2013 Nissan Quest has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2013 Nissan Quest

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan Quest RE52 (fourth generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the Quest

Nissan's immobilizer is called NATS, short for Nissan Anti-Theft System, and nearly every Nissan sold in the US since 2000 has one; a few early pickups and SUVs were built with plain keys. A chip in the key or fob has to answer the car before the engine is allowed to run, and a small security light on the dash blinks while the system is armed. Around 2000, cars such as the Maxima and Altima used the Texas Crypto 4D60 transponder. From about 2003, the 350Z, Armada, Frontier and later Altimas and Maximas moved to the Philips ID46, which stayed inside Nissan's Intelligent Key fobs for about a decade. Intelligent Key proximity fobs arrived first with a twist-knob ignition on Pathfinders, Armadas and the 2007 Maxima, and the 2007 Altima made push-button start standard. Some 2013-era fobs switched to Hitag 3 (ID47), and Hitag AES (4A) took over from the 2016 Maxima, the 2018 Leaf and Kicks, and the 2019 Altima. The newest platforms, including the Ariya, the 2025 Kicks and the 2025 Armada, use current-generation fobs and add security layers that make lost-key work slower. Your model year and the part number inside your fob tell us which system you have.

• Catalogs list a CR2025 cell for both the five-button and six-button Quest fobs.
• The 2017 Quest was built only for fleet sales, so most 2017 vans on the road started out in rental or commercial fleets.

Programming a 2013 Quest key

Fobs are registered through the OBD-II port after we read the security code and obtain the PIN. Absent fobs are erased, so gather every fob first. Because the button layout follows the van's power-door equipment, the replacement must mirror your original. For all-keys-lost, we open the van, decode the driver's lock to cut the emergency key and register new fobs where the van is parked.

Lost every key to your Quest?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Nissan Quest can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2013 Nissan Quest we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Quest key battery

Most fobs for a 2013 Nissan Quest open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2025, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Quest uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Nissan system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a Quest key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Nissan Quest is the most involved of all, both in the part itself and in the programming.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Nissan system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• When a fob battery runs low on a push-button Nissan, the owner's manual procedure is to press the brake and touch the ignition button with the Intelligent Key. The car reads the chip at close range and starts even with weak remote range.
• Making one new key wipes every key that wasn't present for the registration. If an old spare suddenly stops starting the car after a key was added somewhere, that is usually why, and the spare has to be registered again.
• A security light that stays lit after you switch the ignition on, with the engine refusing to start, means NATS doesn't recognize the key: a cracked transponder, a key registered to another car, or an aftermarket remote starter interfering.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2013 Nissan Quest key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Quest in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.