2011 Nissan Quest Key Replacement

2011 Quest key specs

The last Quest, built in Japan by Nissan Shatai, uses an Intelligent Key with push-button start. Its fob adds buttons for the power sliding doors and liftgate on equipped vans; catalogs list a five-button version under FCC ID CWTWB1U818 and a six-button version under CWTWB1U789. A metal emergency key is stored inside the fob for the driver's door. Retail sales ended with the 2016 model year, and a short 2017 run went to fleet buyers with the same key system.

What's specific to the 2011 Quest

2011 was the first model year of the Quest RE52 (fourth generation). Early-production cars sometimes use different part numbers than later ones, so for a 2011 Nissan Quest we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. It also marks a change from the previous generation: the 2009 Quest used a transponder (chip) key and a key with a separate remote fob, while the 2011 uses a smart proximity key with push-button start. Keys from the older car will not work in this one.

A 2011 Nissan Quest is about 15 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models. Smart-key cars like the 2011 Quest can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2011 Nissan Quest

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan Quest RE52 (fourth generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the Quest

• Catalogs list a CR2025 cell for both the five-button and six-button Quest fobs.
• The 2017 Quest was built only for fleet sales, so most 2017 vans on the road started out in rental or commercial fleets.

Programming a 2011 Quest key

Fobs are registered through the OBD-II port after we read the security code and obtain the PIN. Absent fobs are erased, so gather every fob first. Because the button layout follows the van's power-door equipment, the replacement must mirror your original. For all-keys-lost, we open the van, decode the driver's lock to cut the emergency key and register new fobs where the van is parked.

Nissan keys are registered through the OBD-II port under the dash. The car reports a security code from its body control module or immobilizer, and our programmer turns it into the four-digit PIN that opens key registration; many 2013-and-later cars present a longer 20-digit code that needs an online calculation. Registration wipes every key that is not in the car at that moment, so bring all the keys and fobs you want to keep, and Nissan's manuals allow four or five registered keys, depending on the car. On turn-key models from the early 2000s, the separate remote usually pairs through an on-board routine of ignition cycles and button presses, but the transponder key always needs a programmer. Replacement Intelligent Keys must match the original part number, and many newer AES fobs are locked to the first car that learns them. We check your ID and registration before any key work starts.

Lost every key to your Quest?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Nissan Quest can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Quest and your schedule.

Quest key battery

Most fobs for a 2011 Nissan Quest open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2025, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Quest uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Quest, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Quest key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2011 Nissan Quest key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Quest in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.