2019 Nissan NV200 Key Replacement

2019 NV200 key specs

The NV200 starts with a metal key that carries an immobilizer chip in its head. Keyless entry, where fitted, came from a separate remote: supplier catalogs list a four-button 28268ZT remote for 2015-2016 vans and a three-button 28268 remote without years. Because more than one setup appears in catalogs, we look at your existing key and remote before ordering anything. There is no smart key or push-button start on any NV200.

What's specific to the 2019 NV200

The 2019 Nissan NV200 is the seventh of 9 model years in the NV200 M20 (single generation) (2013–2021), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2019 Nissan NV200 is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

If a newly cut key turns the 2019 NV200's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2019 Nissan NV200

• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Nissan NV200, we'll explain which method fits and why.
• Key with separate remote fob. Some Nissan NV200 owners carry two pieces: a transponder key for the ignition and a separate remote fob on the same ring. Because they work independently, you only have to replace what's actually missing or broken. A lost remote still leaves you with a key that opens the doors and starts the engine, so it's an inconvenience rather than an emergency. A lost key is the more urgent half, since it has to be cut and its chip programmed before the car will run. We stock and program both sides, and if the whole ring is gone, we handle the key first and then pair a new remote.

How the Nissan immobilizer works on the NV200

Nissan's immobilizer is called NATS, short for Nissan Anti-Theft System, and nearly every Nissan sold in the US since 2000 has one; a few early pickups and SUVs were built with plain keys. A chip in the key or fob has to answer the car before the engine is allowed to run, and a small security light on the dash blinks while the system is armed. Around 2000, cars such as the Maxima and Altima used the Texas Crypto 4D60 transponder. From about 2003, the 350Z, Armada, Frontier and later Altimas and Maximas moved to the Philips ID46, which stayed inside Nissan's Intelligent Key fobs for about a decade. Intelligent Key proximity fobs arrived first with a twist-knob ignition on Pathfinders, Armadas and the 2007 Maxima, and the 2007 Altima made push-button start standard. Some 2013-era fobs switched to Hitag 3 (ID47), and Hitag AES (4A) took over from the 2016 Maxima, the 2018 Leaf and Kicks, and the 2019 Altima. The newest platforms, including the Ariya, the 2025 Kicks and the 2025 Armada, use current-generation fobs and add security layers that make lost-key work slower. Your model year and the part number inside your fob tell us which system you have.

• The Chevrolet City Express, sold from 2015 to 2018, was built from the NV200 and uses Nissan key hardware.
• With no smart key on any NV200, a correctly cut and programmed chipped key always starts the van, even if the remote is lost.

Programming a 2019 NV200 key

The chipped key is cut, then registered through the OBD-II port with a PIN derived from the van's security code. Registration clears absent keys, so we program every key you want to keep at once. A separate remote can be paired on board by cycling the key in and out of the ignition, turning it to ACC and pressing lock, so replacing a remote alone is often a small job. All-keys-lost is handled on site.

Lost every key to your NV200?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Nissan NV200 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Nissan NV200, ask us directly and you'll get a plain answer.

NV200 key battery

Battery details for the 2019 NV200: CR2025 (separate remote). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your NV200 uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Nissan NV200 keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Nissan system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an NV200 key

• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• A security light that stays lit after you switch the ignition on, with the engine refusing to start, means NATS doesn't recognize the key: a cracked transponder, a key registered to another car, or an aftermarket remote starter interfering.
• Nissan does not keep key numbers on file. The small metal key number plate that came with your keys is the only record, so photograph it and store it outside the car; without it, an all-keys-lost job starts with decoding a lock.
• Push-button Nissans hide a mechanical key inside the fob, released by a small latch on the back. It opens the driver's door when the fob or the 12-volt battery is dead, and on many models it also locks the glove box.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2019 Nissan NV200 key?

The quickest route to a working key for a 2019 Nissan NV200 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.