2013 Nissan NV200 Key Replacement

2013 NV200 key specs

The NV200 starts with a metal key that carries an immobilizer chip in its head. Keyless entry, where fitted, came from a separate remote: supplier catalogs list a four-button 28268ZT remote for 2015-2016 vans and a three-button 28268 remote without years. Because more than one setup appears in catalogs, we look at your existing key and remote before ordering anything. There is no smart key or push-button start on any NV200.

What's specific to the 2013 NV200

2013 was the first model year of the NV200 M20 (single generation). Early-production cars sometimes use different part numbers than later ones, so for a 2013 Nissan NV200 we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. At roughly 13 years old, a 2013 Nissan NV200 has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

If a newly cut key turns the 2013 NV200's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2013 Nissan NV200

• Transponder (chip) key. A transponder key carries a small chip in its head, usually a glass capsule or a carbon wafer, with no battery of its own. When you turn the key in a 2013 Nissan NV200 that uses one, an antenna ring around the ignition energizes the chip and asks for its code. If the answer matches what the immobilizer has stored, the engine is allowed to run. If it doesn't, you get the classic symptoms: the engine cranks but won't fire, or it fires and dies after a second, and the security light on the dash flashes or stays lit. That's why a perfectly cut copy without a programmed chip will open the doors but won't start the car.
• Key with separate remote fob. Pairing a separate remote to a 2013 Nissan NV200 is a different job from programming the ignition key. Some vehicles accept new remotes through an on-board sequence of key turns and button presses; others need a scan tool connected to the OBD-II port. On many of them, entering remote programming mode clears every remote the car already knows, so any remote you want to keep has to be present and re-paired during the same session. Before we start, gather every remote that belongs to the vehicle. Leaving one in a kitchen drawer is a classic way to end up with a remote that quits the day after a new one is added.

How the Nissan immobilizer works on the NV200

Nissan's immobilizer is called NATS, short for Nissan Anti-Theft System, and nearly every Nissan sold in the US since 2000 has one; a few early pickups and SUVs were built with plain keys. A chip in the key or fob has to answer the car before the engine is allowed to run, and a small security light on the dash blinks while the system is armed. Around 2000, cars such as the Maxima and Altima used the Texas Crypto 4D60 transponder. From about 2003, the 350Z, Armada, Frontier and later Altimas and Maximas moved to the Philips ID46, which stayed inside Nissan's Intelligent Key fobs for about a decade. Intelligent Key proximity fobs arrived first with a twist-knob ignition on Pathfinders, Armadas and the 2007 Maxima, and the 2007 Altima made push-button start standard. Some 2013-era fobs switched to Hitag 3 (ID47), and Hitag AES (4A) took over from the 2016 Maxima, the 2018 Leaf and Kicks, and the 2019 Altima. The newest platforms, including the Ariya, the 2025 Kicks and the 2025 Armada, use current-generation fobs and add security layers that make lost-key work slower. Your model year and the part number inside your fob tell us which system you have.

• The Chevrolet City Express, sold from 2015 to 2018, was built from the NV200 and uses Nissan key hardware.
• With no smart key on any NV200, a correctly cut and programmed chipped key always starts the van, even if the remote is lost.

Programming a 2013 NV200 key

The chipped key is cut, then registered through the OBD-II port with a PIN derived from the van's security code. Registration clears absent keys, so we program every key you want to keep at once. A separate remote can be paired on board by cycling the key in and out of the ignition, turning it to ACC and pressing lock, so replacing a remote alone is often a small job. All-keys-lost is handled on site.

Lost every key to your NV200?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2013 Nissan NV200 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

NV200 key battery

Battery details for the 2013 NV200: CR2025 (separate remote). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your NV200 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your NV200, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an NV200 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Nissan NV200 is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• Push-button Nissans hide a mechanical key inside the fob, released by a small latch on the back. It opens the driver's door when the fob or the 12-volt battery is dead, and on many models it also locks the glove box.
• High-mileage Altimas, Maximas and Frontiers from the 2000s often have worn ignition wafers and keys worn smooth. A key cut to factory code, rather than copied from the worn original, usually turns the ignition far more smoothly.
• Making one new key wipes every key that wasn't present for the registration. If an old spare suddenly stops starting the car after a key was added somewhere, that is usually why, and the spare has to be registered again.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2013 Nissan NV200 key?

The quickest route to a working key for a 2013 Nissan NV200 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.