2024 Nissan Murano Key Replacement

2024 Murano key specs

Every third-generation Murano uses an Intelligent Key with push-button start. Fobs come with three, four or five buttons depending on equipment, the extras controlling the power liftgate and factory remote start. Supplier catalogs list FCC ID KR5S180144014 for early fobs and KR5TXN7 for later ones, starting around 2018, and the 2022-2023 four-button fob is the same 9BU5A part listed for the Titan. Each fob holds a mechanical key for the driver's door. With so many versions, the part number inside your current fob is the best guide.

What's specific to the 2024 Murano

2024 was the final model year of the Murano Z52 (third generation), before the Z53 (fourth generation) arrived for 2025. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2024 Nissan Murano matches a 2015.

At 2 years old, a 2024 Nissan Murano is usually still on its original keys and fob batteries. The most common call for a car this new is a second key, since many buyers leave the dealer with only one, or a replacement after a lost fob.

Key options for the 2024 Nissan Murano

• Smart proximity key (push-to-start). A smart or proximity key lets a 2024 Nissan Murano open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Nissan immobilizer works on the Murano

• Catalogs list the five-button KR5TXN7 fob, parts 285E3-9UF7A and 9UF7B, for 2018-2023 Muranos and for 2018-2020 Pathfinders.
• A remote-start button only works on a Murano that left the factory with remote engine start, so match the button count to your old fob.

Programming a 2024 Murano key

We register Murano fobs through the OBD-II port. The car gives up a security code, and depending on the year our equipment converts it to a PIN directly or through an online calculation. All fobs you keep must be present, because registration erases the others. Later fobs in this family are often locked to the first car they learn, so we usually start with a new fob. All-keys-lost is often handled on site after we cut the emergency key from a decoded door lock, depending on the build.

Spare fobs are routine on this generation. Late-model Muranos with newer encrypted fobs can need extra steps or a dealer PIN for all-keys-lost, confirmed by VIN.

Lost every key to your Murano?

If every key is gone, we can usually solve it where the car is parked. First we confirm ownership with your ID and the registration or title. Nissan states in its owner's manuals that it does not keep a record of key numbers, so unless you saved the key number plate, we decode the driver's door lock to cut a mechanical key or emergency blade. Turn-key models then get a new transponder key programmed over OBD-II, and push-button models get new fobs registered with their emergency blades cut to match. Because registration erases the lost keys, a missing key can no longer start the car afterward. The newest platforms, and low-volume cars like the GT-R, can need extra hardware, a dealer-sourced PIN or a dealer visit, and we tell you which case applies before we start.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Nissan Murano can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Nissan Murano, ask us directly and you'll get a plain answer.

Murano key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Murano uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Nissan system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Murano key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Nissan system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• When a fob battery runs low on a push-button Nissan, the owner's manual procedure is to press the brake and touch the ignition button with the Intelligent Key. The car reads the chip at close range and starts even with weak remote range.
• Secondhand Intelligent Keys are a common dead end. Many newer Hitag AES fobs lock to the first car that learns them, and a fob with a different FCC ID or part number won't register even when it looks identical to yours.
• Push-button Nissans hide a mechanical key inside the fob, released by a small latch on the back. It opens the driver's door when the fob or the 12-volt battery is dead, and on many models it also locks the glove box.
• Nissan manuals warn against leaving the Intelligent Key anywhere above 140 degrees Fahrenheit. A fob left on the dash of a parked car during an Inland Empire summer can get that hot, which shortens battery life and can damage the circuit board.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2024 Nissan Murano key?

Need a key for your 2024 Nissan Murano? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.