2015 Nissan Murano Key Replacement

2015 Murano key specs

Every third-generation Murano uses an Intelligent Key with push-button start. Fobs come with three, four or five buttons depending on equipment, the extras controlling the power liftgate and factory remote start. Supplier catalogs list FCC ID KR5S180144014 for early fobs and KR5TXN7 for later ones, starting around 2018, and the 2022-2023 four-button fob is the same 9BU5A part listed for the Titan. Each fob holds a mechanical key for the driver's door. With so many versions, the part number inside your current fob is the best guide.

What's specific to the 2015 Murano

2015 was the first model year of the Murano Z52 (third generation). Early-production cars sometimes use different part numbers than later ones, so for a 2015 Nissan Murano we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. The key looks similar to the 2014 model's, but the chip moved from Philips ID46 to Hitag AES (4A) on KR5TXN7-family fobs, so an older key is not a substitute.

At roughly 11 years old, a 2015 Nissan Murano has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit. Smart-key cars like the 2015 Murano can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2015 Nissan Murano

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan Murano Z52 (third generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the Murano

• Catalogs list the five-button KR5TXN7 fob, parts 285E3-9UF7A and 9UF7B, for 2018-2023 Muranos and for 2018-2020 Pathfinders.
• A remote-start button only works on a Murano that left the factory with remote engine start, so match the button count to your old fob.

Programming a 2015 Murano key

We register Murano fobs through the OBD-II port. The car gives up a security code, and depending on the year our equipment converts it to a PIN directly or through an online calculation. All fobs you keep must be present, because registration erases the others. Later fobs in this family are often locked to the first car they learn, so we usually start with a new fob. All-keys-lost is often handled on site after we cut the emergency key from a decoded door lock, depending on the build.

Spare fobs are routine on this generation. Late-model Muranos with newer encrypted fobs can need extra steps or a dealer PIN for all-keys-lost, confirmed by VIN.

Lost every key to your Murano?

If every key is gone, we can usually solve it where the car is parked. First we confirm ownership with your ID and the registration or title. Nissan states in its owner's manuals that it does not keep a record of key numbers, so unless you saved the key number plate, we decode the driver's door lock to cut a mechanical key or emergency blade. Turn-key models then get a new transponder key programmed over OBD-II, and push-button models get new fobs registered with their emergency blades cut to match. Because registration erases the lost keys, a missing key can no longer start the car afterward. The newest platforms, and low-volume cars like the GT-R, can need extra hardware, a dealer-sourced PIN or a dealer visit, and we tell you which case applies before we start.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2015 Nissan Murano we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Murano key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Murano uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Nissan Murano keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Murano, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Murano key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Murano came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Nissan system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• Push-button Nissans hide a mechanical key inside the fob, released by a small latch on the back. It opens the driver's door when the fob or the 12-volt battery is dead, and on many models it also locks the glove box.
• Secondhand Intelligent Keys are a common dead end. Many newer Hitag AES fobs lock to the first car that learns them, and a fob with a different FCC ID or part number won't register even when it looks identical to yours.
• Nissan manuals warn against leaving the Intelligent Key anywhere above 140 degrees Fahrenheit. A fob left on the dash of a parked car during an Inland Empire summer can get that hot, which shortens battery life and can damage the circuit board.
• Making one new key wipes every key that wasn't present for the registration. If an old spare suddenly stops starting the car after a key was added somewhere, that is usually why, and the spare has to be registered again.

Tips from a mobile locksmith

• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2015 Nissan Murano key?

The quickest route to a working key for a 2015 Nissan Murano starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.