2020 Nissan GT-R Key Replacement

2020 GT-R key specs

Every GT-R uses an Intelligent Key with lock, unlock, trunk and panic buttons, a mechanical emergency key inside, and push-button start. The fob carries FCC ID KR55WK49622, the same family used on Altimas and Maximas of the era, but with a GT-R part number and an emergency key listed under its own part. Request switches on the door handles lock and open the car with the fob nearby. A generic Nissan fob that looks similar will not substitute.

What's specific to the 2020 GT-R

The 2020 Nissan GT-R is the twelfth of 13 model years in the GT-R R35 (2009-2021 model years) (2009–2021), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2020 Nissan GT-R is about 6 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2020 Nissan GT-R

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan GT-R R35 (2009-2021 model years), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the GT-R

• Supplier catalogs list fob part 285E3-JF87A for 2009-2020 GT-R cars, with emergency key part H0564-JF00A.
• Nissan did not offer a 2022 GT-R in North America, so there is no 2022 model-year car to match a key to.

Programming a 2020 GT-R key

GT-R fobs register through the OBD-II port with a PIN calculated from the body control module's code, much like other Nissans of the period. In practice, matching the exact GT-R part number matters, and all-keys-lost on some years can require dealer software. We confirm your VIN, the part number and our equipment coverage before you order a fob, so you don't pay for a key that won't register.

Nissan keys are registered through the OBD-II port under the dash. The car reports a security code from its body control module or immobilizer, and our programmer turns it into the four-digit PIN that opens key registration; many 2013-and-later cars present a longer 20-digit code that needs an online calculation. Registration wipes every key that is not in the car at that moment, so bring all the keys and fobs you want to keep, and Nissan's manuals allow four or five registered keys, depending on the car. On turn-key models from the early 2000s, the separate remote usually pairs through an on-board routine of ignition cycles and button presses, but the transponder key always needs a programmer. Replacement Intelligent Keys must match the original part number, and many newer AES fobs are locked to the first car that learns them. We check your ID and registration before any key work starts.

Spare fobs are often possible with the correct GT-R part; all-keys-lost or some years may need a dealer, confirmed by VIN.

Lost every key to your GT-R?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Nissan GT-R can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Nissan GT-R requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Nissan GT-R, ask us directly and you'll get a plain answer.

GT-R key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your GT-R uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your GT-R, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a GT-R key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Nissan GT-R is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2020 Nissan GT-R key?

Don't wait until the last key disappears. If your Nissan GT-R is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.