2012 Nissan GT-R Key Replacement

2012 GT-R key specs

Every GT-R uses an Intelligent Key with lock, unlock, trunk and panic buttons, a mechanical emergency key inside, and push-button start. The fob carries FCC ID KR55WK49622, the same family used on Altimas and Maximas of the era, but with a GT-R part number and an emergency key listed under its own part. Request switches on the door handles lock and open the car with the fob nearby. A generic Nissan fob that looks similar will not substitute.

What's specific to the 2012 GT-R

The 2012 Nissan GT-R is the fourth of 13 model years in the GT-R R35 (2009-2021 model years) (2009–2021), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 14 years old, a 2012 Nissan GT-R has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2012 GT-R can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2012 Nissan GT-R

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan GT-R R35 (2009-2021 model years), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the GT-R

• Supplier catalogs list fob part 285E3-JF87A for 2009-2020 GT-R cars, with emergency key part H0564-JF00A.
• Nissan did not offer a 2022 GT-R in North America, so there is no 2022 model-year car to match a key to.

Programming a 2012 GT-R key

GT-R fobs register through the OBD-II port with a PIN calculated from the body control module's code, much like other Nissans of the period. In practice, matching the exact GT-R part number matters, and all-keys-lost on some years can require dealer software. We confirm your VIN, the part number and our equipment coverage before you order a fob, so you don't pay for a key that won't register.

Spare fobs are often possible with the correct GT-R part; all-keys-lost or some years may need a dealer, confirmed by VIN.

Lost every key to your GT-R?

If every key is gone, we can usually solve it where the car is parked. First we confirm ownership with your ID and the registration or title. Nissan states in its owner's manuals that it does not keep a record of key numbers, so unless you saved the key number plate, we decode the driver's door lock to cut a mechanical key or emergency blade. Turn-key models then get a new transponder key programmed over OBD-II, and push-button models get new fobs registered with their emergency blades cut to match. Because registration erases the lost keys, a missing key can no longer start the car afterward. The newest platforms, and low-volume cars like the GT-R, can need extra hardware, a dealer-sourced PIN or a dealer visit, and we tell you which case applies before we start.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2012 Nissan GT-R we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

GT-R key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your GT-R uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Nissan system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a GT-R key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Nissan GT-R is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• Nissan manuals warn against leaving the Intelligent Key anywhere above 140 degrees Fahrenheit. A fob left on the dash of a parked car during an Inland Empire summer can get that hot, which shortens battery life and can damage the circuit board.
• Push-button Nissans hide a mechanical key inside the fob, released by a small latch on the back. It opens the driver's door when the fob or the 12-volt battery is dead, and on many models it also locks the glove box.
• High-mileage Altimas, Maximas and Frontiers from the 2000s often have worn ignition wafers and keys worn smooth. A key cut to factory code, rather than copied from the worn original, usually turns the ignition far more smoothly.
• Nissan does not keep key numbers on file. The small metal key number plate that came with your keys is the only record, so photograph it and store it outside the car; without it, an all-keys-lost job starts with decoding a lock.

Tips from a mobile locksmith

• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2012 Nissan GT-R key?

Don't wait until the last key disappears. If your Nissan GT-R is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.