2019 Mitsubishi Outlander Key Replacement

2019 Outlander key specs

The entry ES trim kept a turn key: a three-button remote-head key on an MIT3 blade, updated around 2016 to a newer design with FCC ID OUCJ166N. SE, SEL and GT trims use FAST-key with a push-button engine switch. Their smart fob comes in two versions, a three-button fob and a four-button fob that adds a power liftgate button on trucks equipped with one. Both hold an emergency blade for the driver's door, and both run on a CR2032.

What's specific to the 2019 Outlander

The 2019 Mitsubishi Outlander is the sixth of 7 model years in the Outlander GF (third generation) (2014–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2019 Mitsubishi Outlander is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2019 Mitsubishi Outlander

• Remote head key. Remote-head keys look similar across many vehicles, but the electronics inside are not interchangeable. Getting the right one for a Mitsubishi Outlander means matching the FCC ID and part number printed on the back or inside the case, the operating frequency, which is commonly 315 MHz on US-market cars, the transponder type, and the button layout. A trim with remote start or a power liftgate may use a four- or five-button version where a base trim uses three. We check those details against your VIN and your existing key, if you have one, before cutting the blade. A wrong match can look perfect and still refuse to program.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Mitsubishi Outlander GF (third generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Mitsubishi immobilizer works on the Outlander

Mitsubishi's US key history splits into a handful of eras, and the model year usually tells us which one we're dealing with. Around 2000, the larger models got Texas Instruments transponders: the Diamante, Montero and Montero Sport on the MIT1 key, and the Eclipse and Galant on the MIT6 key, with the chip moving from 4D60 to 4D61 around the middle of 2001. Small cars such as the Mirage and the 2002-2007 Lancer generally kept plain cut keys, although the Lancer Evolution did not. Philips ID46 chips appeared on the redesigned 2004 Galant, remote-head keys followed in 2006, and the blade changed from the straight MIT6 to the shouldered MIT3 during the 2007 model year. The 2007 Outlander and 2008 Lancer introduced FAST-key, Mitsubishi's keyless operation system, which carried on through the Lancer Evolution X and the Outlander Sport. Later Mirage, Eclipse Cross and Outlander Sport smart keys are newer designs that need their own tool coverage, and the Nissan-based 2022-on Outlander uses an AES-encrypted fob. The Dodge Dakota-based Raider pickup follows Chrysler's Sentry Key rules instead.

• The four-button smart fob with a liftgate button is Mitsubishi part 8637A817; the three-button version is 8637A316.
• Supplier listings tie the OUCJ166N remote-head key (part 6370B944) to Outlanders from 2016 on and to the 2016-2017 Lancer.
• There was no 2021 model year of the gasoline Outlander in the US; the next generation arrived as a 2022 model.

Programming a 2019 Outlander key

Both key types are added through the OBD-II port with a programmer and the vehicle PIN; there is no owner programming. Smart fobs must be new or properly unlocked, and the emergency blade is cut separately to the door lock. Aftermarket equipment generally covers spare keys on this generation and all-keys-lost on most trucks, so a lost-key call is usually handled where the vehicle sits once we verify ownership, with push-button trucks checked by VIN first.

Lost every key to your Outlander?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Mitsubishi Outlander can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2019 Mitsubishi Outlander we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Outlander key battery

Battery details for the 2019 Outlander: CR1620 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Outlander uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Mitsubishi Outlander keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Mitsubishi keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Outlander, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Outlander key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Outlander came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mitsubishi key problems

• Key registration on many Mitsubishis wipes every stored key and relearns only the ones present. A spare left at home during the appointment stops working afterward, so gather every key you want to keep before we start.
• Eclipse and Galant models built in 2000 and early 2001 use a Texas 4D60 key, while later 2001 cars use 4D61. A key stamped R on the blade is the early type and one stamped N is the later type, and the wrong chip will turn the locks but not start the engine.
• Remote-head keys on the 2006-2007 Eclipse, Galant and Endeavor came with either a straight MIT6 blade or a shouldered MIT3 blade depending on build date. Check which one your old key has before ordering, because the two are not interchangeable.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2019 Mitsubishi Outlander key?

Don't wait until the last key disappears. If your Mitsubishi Outlander is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.