2009 Mitsubishi Lancer Evolution Key Replacement

2009 Lancer Evolution key specs

The Evolution X uses the same key hardware as the 2008-2017 Lancer. Depending on trim and options, a car has either a four-button remote-head key on the MIT3 blade with a Philips ID46 chip, or FAST-key, which works through request buttons on the doors and replaces the ignition key with a twist knob. The FAST-key fob holds an emergency blade for the driver's door and runs on a CR2032. We check which system your car has before ordering anything.

What's specific to the 2009 Lancer Evolution

The 2009 Mitsubishi Lancer Evolution is the second of 8 model years in the Lancer Evolution CZ4A (Evolution X) (2008–2015), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2009 Mitsubishi Lancer Evolution is about 17 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Smart-key cars like the 2009 Lancer Evolution can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2009 Mitsubishi Lancer Evolution

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2009 Mitsubishi Lancer Evolution with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2009 Mitsubishi Lancer Evolution open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Mitsubishi immobilizer works on the Lancer Evolution

• The Evolution X shares its key hardware with the Lancer of the same years, so Lancer FCC IDs such as OUC644M-KEY-N and OUCG8D-625M-A are the starting point.
• Evolution X production ended in 2016, and EPA listings show 2015 as its final US model year.

Programming a 2009 Lancer Evolution key

Programming matches the regular Lancer: remote-head keys and FAST-key fobs are registered through the OBD-II port with a programmer and the security PIN, and the registration clears and relearns all keys. Used fobs must be unlocked before they will learn. For all-keys-lost, we decode the door lock, cut the blade or emergency insert, and register at least two keys on site.

Lost every key to your Lancer Evolution?

If every key to your Mitsubishi is gone, the first job is a working blade. We decode the driver's door lock or cut from a key code the dealer releases by VIN with proof of ownership. Then the immobilizer PIN is obtained and new keys are registered at the car, at least two, which also drops the lost keys from memory. FAST-key and newer smart-key cars need a new fob plus its emergency insert, and remote-head keys need the blade cut and the buttons paired. Most turn-key and older FAST-key models are handled where they sit. Newer smart keys on some Mirage, Eclipse Cross and Outlander Sport builds, plus the 2022-and-later Outlander and Outlander PHEV, may need a dealer PIN or a dealer visit, and we tell you before you commit. Expect to show ID first.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Mitsubishi Lancer Evolution can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Mitsubishi Lancer Evolution requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Mitsubishi Lancer Evolution, ask us directly and you'll get a plain answer.

Lancer Evolution key battery

Battery details for the 2009 Lancer Evolution: CR1620 (remote-head key); CR2032 (FAST-key fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Lancer Evolution uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Mitsubishi Lancer Evolution keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Mitsubishi system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Lancer Evolution key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Mitsubishi Lancer Evolution is the most involved of all, both in the part itself and in the programming.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Mitsubishi system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mitsubishi key problems

• The 2007 Outlander used a one-year FAST-key fob, FCC ID OUCG8D-640M-KEY-N, that differs from the OUC644M-KEY-N fob used from 2008 on. Ordering by model name alone often brings the wrong part.
• Remote-head keys on the 2006-2007 Eclipse, Galant and Endeavor came with either a straight MIT6 blade or a shouldered MIT3 blade depending on build date. Check which one your old key has before ordering, because the two are not interchangeable.
• Remote-head keys and smart fobs take different coin cells: the remote-head keys use a thin CR1620, while FAST-key and smart fobs use a CR2032. A cell of the wrong thickness may not make good contact, so read the old battery before buying.
• Mirage hatchbacks built before about March 2014 use the same FAST-key fob as the Outlander, while later Mirage fobs are a different design. The build date on the driver's door-jamb label settles which one you need.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2009 Mitsubishi Lancer Evolution key?

Need a key for your 2009 Mitsubishi Lancer Evolution? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.