2007 Mitsubishi Endeavor Key Replacement

2007 Endeavor key specs

From 2006, the Endeavor uses a three-button remote-head key (lock, unlock, panic) with FCC ID OUCG8D-620M-A and a Philips ID46 chip. The 2006 and some early 2007 trucks have a straight MIT6 blade, while later trucks have a shouldered MIT3 blade, and supplier listings warn that 2007 models can have either. A plain ID46 transponder key without buttons is available as a spare. The remote-head key runs on a CR1620.

What's specific to the 2007 Endeavor

The 2007 Mitsubishi Endeavor is the second of 6 model years in the Endeavor First generation (remote-head key years) (2006–2011), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2007 Mitsubishi Endeavor is about 19 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2007 Mitsubishi Endeavor

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2007 Mitsubishi Endeavor with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Transponder (chip) key. A transponder key carries a small chip in its head, usually a glass capsule or a carbon wafer, with no battery of its own. When you turn the key in a 2007 Mitsubishi Endeavor that uses one, an antenna ring around the ignition energizes the chip and asks for its code. If the answer matches what the immobilizer has stored, the engine is allowed to run. If it doesn't, you get the classic symptoms: the engine cranks but won't fire, or it fires and dies after a second, and the security light on the dash flashes or stays lit. That's why a perfectly cut copy without a programmed chip will open the doors but won't start the car.

How the Mitsubishi immobilizer works on the Endeavor

Mitsubishi's US key history splits into a handful of eras, and the model year usually tells us which one we're dealing with. Around 2000, the larger models got Texas Instruments transponders: the Diamante, Montero and Montero Sport on the MIT1 key, and the Eclipse and Galant on the MIT6 key, with the chip moving from 4D60 to 4D61 around the middle of 2001. Small cars such as the Mirage and the 2002-2007 Lancer generally kept plain cut keys, although the Lancer Evolution did not. Philips ID46 chips appeared on the redesigned 2004 Galant, remote-head keys followed in 2006, and the blade changed from the straight MIT6 to the shouldered MIT3 during the 2007 model year. The 2007 Outlander and 2008 Lancer introduced FAST-key, Mitsubishi's keyless operation system, which carried on through the Lancer Evolution X and the Outlander Sport. Later Mirage, Eclipse Cross and Outlander Sport smart keys are newer designs that need their own tool coverage, and the Nissan-based 2022-on Outlander uses an AES-encrypted fob. The Dodge Dakota-based Raider pickup follows Chrysler's Sentry Key rules instead.

• Ilco lists the MIT16A-PT (straight blade) for 2006-2007 Endeavors and the MIT17A-PT (shouldered blade) for 2007-2011.
• The Endeavor's three-button key has no trunk button, so it doesn't swap with the four-button Eclipse and Galant keys.

Programming a 2007 Endeavor key

We program the chip and the remote buttons through the OBD-II port with a programmer and the security PIN; there's no owner routine. Used keys need unlocking before they'll learn. When all keys are lost, decoding the door lock tells us which blade style your truck takes, and we cut and register at least two keys at the vehicle.

Lost every key to your Endeavor?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Mitsubishi Endeavor can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Mitsubishi Endeavor requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Mitsubishi Endeavor, ask us directly and you'll get a plain answer.

Endeavor key battery

Most fobs for a 2007 Mitsubishi Endeavor open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR1620, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Endeavor uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Mitsubishi keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Endeavor, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an Endeavor key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Mitsubishi Endeavor is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mitsubishi key problems

• Remote-head keys on the 2006-2007 Eclipse, Galant and Endeavor came with either a straight MIT6 blade or a shouldered MIT3 blade depending on build date. Check which one your old key has before ordering, because the two are not interchangeable.
• Inland Empire heat drains fob batteries faster than the calendar suggests. On FAST-key cars, a key warning on the dash or a fob that only works up close usually means a weak CR2032, an easy fix before it strands you.
• The 2007 Outlander used a one-year FAST-key fob, FCC ID OUCG8D-640M-KEY-N, that differs from the OUC644M-KEY-N fob used from 2008 on. Ordering by model name alone often brings the wrong part.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2007 Mitsubishi Endeavor key?

Don't wait until the last key disappears. If your Mitsubishi Endeavor is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.