2016 Lincoln MKS Key Replacement

2016 MKS key specs

Facelifted MKS sedans use the five-button Intelligent Access fob catalogued under FCC ID M3N5WY8609, a 315 MHz smart key with a CR2032 battery. Its emergency blade is the Ford 8-cut H75 profile, the same insert listed for the 2011-2015 MKX and the MKT. The SecuriCode Invisible keypad on the driver's B-pillar is a touch panel that can hold extra codes, useful for someone who needs to get into the car without carrying a fob.

What's specific to the 2016 MKS

2016 was the final model year of the MKS First generation (2013 facelift). Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2016 Lincoln MKS matches a 2013. At roughly 10 years old, a 2016 Lincoln MKS has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2016 MKS can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2016 Lincoln MKS

• Smart proximity key (push-to-start). A smart or proximity key lets a 2016 Lincoln MKS open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Lincoln immobilizer works on the MKS

Every Lincoln from the 2000 model year on uses Ford's Passive Anti-Theft System, PATS, which Ford also markets as SecuriLock. A transponder in the key head, or inside the fob on push-button cars, answers a challenge from the car, and the engine won't run unless that code matches a key stored in memory. The hardware changed in clear steps. The Town Car, Continental and Navigator through 2002, plus the 2002 Blackwood, use a Texas 4C fixed-code chip in a Ford 8-cut key. The 2000-2002 LS used a Texas 4D60 chip, and from 2003 the line moved to Texas 4D63 keys. Remote-head keys, with the lock buttons molded into the key, show up from the 2006 Zephyr on. Intelligent Access with push-button start arrived on the 2009 MKS, using 315 MHz fobs with a Philips ID46 chip and a hidden emergency blade. The 2013 MKZ introduced 902 MHz fobs with NXP Hitag Pro encryption and an HU101 emergency blade, while the MKX, MKS, MKT and Navigator kept the older 315 MHz style for several more years. The 2020 Aviator and Corsair added Phone As A Key, which lets a paired smartphone act as the key.

• Catalogs list Strattec 5912345 (Ford 164-R8041) as the emergency blade for 2013-2016 MKS fobs.
• A SecuriCode code can let someone into the car without letting them drive it, and the code is easy to change.

Programming a 2016 MKS key

Fobs are registered over OBD-II with a programmer after Ford's security access, and the H75 emergency blade is cut to code. With one fob still working, adding a spare is straightforward. For all-keys-lost, most of these cars are handled at the OBD-II port, but 2016 cars can need an emulator cable, and we confirm which applies by VIN before starting.

Spare fobs are routine; all-keys-lost is normally done at the OBD-II port, but 2016 cars can need an emulator cable, which we confirm by VIN.

Lost every key to your MKS?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Lincoln MKS, ask us directly and you'll get a plain answer.

MKS key battery

Most fobs for a 2016 Lincoln MKS open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your MKS uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your MKS, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an MKS key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Lincoln MKS is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Lincoln key problems

• Town Cars spent years in livery service, so plenty of them have very high mileage, along with worn keys and ignition cylinders. Cutting a fresh key to code, rather than copying a worn one, usually restores a smooth turn.
• Inland Empire summer heat drains fob batteries faster. Lincoln fobs from about 2017 on take a CR2450, while many earlier remotes and 315 MHz smart keys use a CR2032, so read the old cell before buying a replacement.
• A rapidly flashing theft light with a no-start, or an engine that dies right away, usually means PATS didn't read the key. A cracked key head with a loose chip, or a hardware-store copy without the right transponder, is the usual cause.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2016 Lincoln MKS key?

The quickest route to a working key for a 2016 Lincoln MKS starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.