2013 Lincoln MKS Key Replacement

2013 MKS key specs

Facelifted MKS sedans use the five-button Intelligent Access fob catalogued under FCC ID M3N5WY8609, a 315 MHz smart key with a CR2032 battery. Its emergency blade is the Ford 8-cut H75 profile, the same insert listed for the 2011-2015 MKX and the MKT. The SecuriCode Invisible keypad on the driver's B-pillar is a touch panel that can hold extra codes, useful for someone who needs to get into the car without carrying a fob.

What's specific to the 2013 MKS

2013 was the first model year of the MKS First generation (2013 facelift). Early-production cars sometimes use different part numbers than later ones, so for a 2013 Lincoln MKS we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. It also marks a change from the previous generation: the 2012 MKS used a smart proximity key with push-button start and a remote head key, while the 2013 uses a smart proximity key with push-button start. Keys from the older car will not work in this one.

At roughly 13 years old, a 2013 Lincoln MKS has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2013 Lincoln MKS

• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2013 Lincoln MKS is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Lincoln immobilizer works on the MKS

Every Lincoln from the 2000 model year on uses Ford's Passive Anti-Theft System, PATS, which Ford also markets as SecuriLock. A transponder in the key head, or inside the fob on push-button cars, answers a challenge from the car, and the engine won't run unless that code matches a key stored in memory. The hardware changed in clear steps. The Town Car, Continental and Navigator through 2002, plus the 2002 Blackwood, use a Texas 4C fixed-code chip in a Ford 8-cut key. The 2000-2002 LS used a Texas 4D60 chip, and from 2003 the line moved to Texas 4D63 keys. Remote-head keys, with the lock buttons molded into the key, show up from the 2006 Zephyr on. Intelligent Access with push-button start arrived on the 2009 MKS, using 315 MHz fobs with a Philips ID46 chip and a hidden emergency blade. The 2013 MKZ introduced 902 MHz fobs with NXP Hitag Pro encryption and an HU101 emergency blade, while the MKX, MKS, MKT and Navigator kept the older 315 MHz style for several more years. The 2020 Aviator and Corsair added Phone As A Key, which lets a paired smartphone act as the key.

• Catalogs list Strattec 5912345 (Ford 164-R8041) as the emergency blade for 2013-2016 MKS fobs.
• A SecuriCode code can let someone into the car without letting them drive it, and the code is easy to change.

Programming a 2013 MKS key

Fobs are registered over OBD-II with a programmer after Ford's security access, and the H75 emergency blade is cut to code. With one fob still working, adding a spare is straightforward. For all-keys-lost, most of these cars are handled at the OBD-II port, but 2016 cars can need an emulator cable, and we confirm which applies by VIN before starting.

Spare fobs are routine; all-keys-lost is normally done at the OBD-II port, but 2016 cars can need an emulator cable, which we confirm by VIN.

Lost every key to your MKS?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Lincoln MKS can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Lincoln MKS requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Lincoln MKS, ask us directly and you'll get a plain answer.

MKS key battery

Most fobs for a 2013 Lincoln MKS open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your MKS uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your MKS, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an MKS key

• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Lincoln system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Lincoln key problems

• Many Lincolns carry a SecuriCode keypad on the driver's door or B-pillar. If the wallet card with the five-digit factory code is gone, the code can usually be read with a scan tool, and you can then add a personal code.
• Inland Empire summer heat drains fob batteries faster. Lincoln fobs from about 2017 on take a CR2450, while many earlier remotes and 315 MHz smart keys use a CR2032, so read the old cell before buying a replacement.
• Town Cars spent years in livery service, so plenty of them have very high mileage, along with worn keys and ignition cylinders. Cutting a fresh key to code, rather than copying a worn one, usually restores a smooth turn.

Tips from a mobile locksmith

• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2013 Lincoln MKS key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your MKS in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.