2007 Jaguar XK Key Replacement

2007 XK key specs

Every X150 XK and XKR uses Jaguar's first Smart Key, FCC ID KR55WK49244, with five buttons (lock, unlock, trunk, panic and lights) and a hidden HU101 emergency blade. With the fob in the cabin, a start button brings the car to life instead of a conventional ignition lock. The same fob appears on the 2009-2013 XF, and the XKR-S and convertible versions share it. A weak CR2032 battery is a common cause of intermittent no-start or not-detected warnings.

What's specific to the 2007 XK

2007 was the first model year of the XK X150. Early-production cars sometimes use different part numbers than later ones, so for a 2007 Jaguar XK we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. It also marks a change from the previous generation: the 2006 XK used a transponder (chip) key and a key with a separate remote fob, while the 2007 uses a smart proximity key with push-button start. Keys from the older car will not work in this one.

A 2007 Jaguar XK is about 19 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models. Smart-key cars like the 2007 XK can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2007 Jaguar XK

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Jaguar XK X150, we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Jaguar immobilizer works on the XK

Jaguar keys from 2000 on fall into four families, and knowing which one your car uses explains most of what a key job involves. The XJ8 (through 2003) and XK8 (through 2006) carried over from the late 1990s and use an 8-cut Tibbe key plus a separate four-button remote; on 2000-2003 cars the transponder is a Megamos crypto (ID48) chip. The S-Type, X-Type and 2004-2009 XJ share a Ford-era immobilizer and a 6-cut Tibbe key carrying a Texas Instruments 4D60 chip, usually built into a flip remote. Jaguar's Smart Key arrived with the 2007 XK and 2009 XF, a proximity fob with a Hitag2 (ID46) transponder and push-button start. From the 2011 XJ, and then the XF, F-Type, XE and F-Pace, Jaguar moved to the KOBJTF10A fob it shares with Land Rover, which uses a Hitag Pro (ID49) transponder and an HU101 emergency blade. On smart-key cars the key data lives in a keyless vehicle module (KVM), called the remote function actuator (RFA) on later models, and its software version decides how a key can be added. The E-Pace, I-Pace and the facelifted cars from about 2020 use newer fob families, where aftermarket coverage is thinner.

• The X150 XK introduced Jaguar's Smart Key system, which carried over to the first XF.
• KR55WK49244 fobs use a Hitag2 (ID46) transponder and operate at 315 MHz in US cars.
• The hidden HU101 emergency blade opens the driver's door if the fob or car battery is dead.

Programming a 2007 XK key

The XK's Hitag2 (ID46) smart key is added over OBD-II with a programmer that covers early Jaguar smart-key systems. With a working key this is a routine spare. With none, the security data may need to be read from the keyless module, which takes longer and on some cars sends the job to the dealer. We confirm coverage for your VIN before quoting and test every function before finishing.

Spare keys are generally doable; all-keys-lost may require reading the keyless module, and some cars need the dealer.

Lost every key to your XK?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Jaguar XK can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Jaguar XK requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2007 Jaguar XK we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

XK key battery

Most fobs for a 2007 Jaguar XK open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your XK uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Jaguar system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an XK key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your XK came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Jaguar key problems

• Tibbe keys on 2000s Jaguars wear along with the ignition and door locks. A key cut to factory code, rather than copied from a worn original, usually works far better in a tired ignition cylinder.
• Owners often forget the mechanical emergency blade hidden inside the smart key. If the fob or car battery dies, that blade fits a driver's door cylinder that on many models sits under a small cap on the handle.
• Flip-key hinges on the S-Type, X-Type and 2004-2009 XJ wear out, leaving a blade that flops or won't lock open. The 4D60 chip and circuit board usually survive, so a new shell and blade can save the original remote.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2007 Jaguar XK key?

Don't wait until the last key disappears. If your Jaguar XK is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.