2020 Ford Fusion Key Replacement

2020 Fusion key specs

The 2017 refresh brought Ford's newer smart fob, a slimmer design shared with the Edge, Explorer and 2018-2020 Mustang, still with a Hitag Pro ID49 transponder and a removable emergency blade. Supplier catalogs continue to list the flip key for the 2017 model year, which covers base cars that kept a turned key; later Fusions generally use the smart fob and push-button start. Smart fobs with a remote-start button were also sold, and those need their own matching part.

What's specific to the 2020 Fusion

2020 was the final model year of the Fusion Second generation refresh. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2020 Ford Fusion matches a 2017. A 2020 Ford Fusion is about 6 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2020 Fusion can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2020 Ford Fusion

• Smart proximity key (push-to-start). A smart or proximity key lets a 2020 Ford Fusion open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.
• Flip (switchblade) key. The hinge is the weak point on most flip keys. The pivot pin loosens, the spring loses tension, the release button sticks, and eventually the blade either won't lock open or flops out on its own. Carrying the key half-open in a pocket speeds that wear along. If the electronics are healthy, a replacement shell with a new hinge and pin often brings a 2020 Ford Fusion flip key back to crisp action: we transfer the board and chip, move or recut the blade, and test every function. If the board has broken solder joints or water corrosion, we'll show you the damage and quote a new key instead.

How the Ford immobilizer works on the Fusion

• This smart fob, FCC ID M3N-A2C93142300, takes a CR2450 battery, not the CR2032 used in the earlier fob.
• The emergency blade in these fobs is Ford part 164-R8168, cut to the same HU101 profile as the door lock.

Programming a 2020 Fusion key

Smart fobs are added through the OBD-II port with a programmer that supports Ford's PATS security access, and we then cut the emergency blade on a laser-style machine. The same tool handles the 2017 flip key. With every key gone, we gain entry and cut a blade, and an active alarm can call for an emulator or bypass cable before we program new fobs. Your ID and registration are checked before we start.

Nearly all Ford key programming runs through the OBD-II port. On turn-key Fords from roughly 2000 to 2014, our programmer requests PATS security access, often a timed wait of about ten minutes, and then adds a key or erases and rebuilds the key list. If you already have two working keys, many of these vehicles also accept Ford's owner procedure, where each good key is switched on in turn, followed by the newly cut key. A fixed-code 4C key can simply be cloned. Most separate remotes from that era pair when the ignition is cycled eight times in quick succession, while integrated remote-head keys usually learn their buttons along with the chip. Hitag Pro flip keys and every push-button fob are registered with a programmer. On many 2015-and-later models an active alarm means an emulator or bypass cable for all-keys-lost work, and some 2020-and-later models add an online authorization step. We check your ID and registration or title before we start.

Spare fobs are routine; all-keys-lost on these push-button Fusions generally needs an emulator or bypass cable, which we confirm by VIN first.

Lost every key to your Fusion?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ford Fusion requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Fusion and your schedule.

Fusion key battery

Battery details for the 2020 Fusion: CR2450 (smart fob); CR2032 (flip key). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Fusion uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ford keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ford system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Fusion key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2020 Ford Fusion key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Fusion in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.