2019 Ford Fusion Key Replacement

2019 Fusion key specs

The 2017 refresh brought Ford's newer smart fob, a slimmer design shared with the Edge, Explorer and 2018-2020 Mustang, still with a Hitag Pro ID49 transponder and a removable emergency blade. Supplier catalogs continue to list the flip key for the 2017 model year, which covers base cars that kept a turned key; later Fusions generally use the smart fob and push-button start. Smart fobs with a remote-start button were also sold, and those need their own matching part.

What's specific to the 2019 Fusion

The 2019 Ford Fusion is the third of 4 model years in the Fusion Second generation refresh (2017–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2019 Ford Fusion is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2019 Fusion can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2019 Ford Fusion

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Ford Fusion Second generation refresh, we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.
• Flip (switchblade) key. The hinge is the weak point on most flip keys. The pivot pin loosens, the spring loses tension, the release button sticks, and eventually the blade either won't lock open or flops out on its own. Carrying the key half-open in a pocket speeds that wear along. If the electronics are healthy, a replacement shell with a new hinge and pin often brings a 2019 Ford Fusion flip key back to crisp action: we transfer the board and chip, move or recut the blade, and test every function. If the board has broken solder joints or water corrosion, we'll show you the damage and quote a new key instead.

How the Ford immobilizer works on the Fusion

Ford's immobilizer is PATS, the Passive Anti-Theft System, sold under the SecuriLock name. A transponder sealed in the key head, or built into the fob on push-button models, answers a coded challenge from a coil around the ignition or from antennas in the cabin, and the engine won't run until the powertrain computer accepts the answer. Across 2000-2026 the chip changed in clear steps. Pickups, big SUVs and the Crown Victoria used a fixed-code Texas 4C chip into the early 2000s, and the Excursion kept it through 2005. The first Escape and early Focus used a Texas 4D60. Between 2000 and 2004 most of the lineup moved to the encrypted Texas 4D63, with 80-bit versions becoming the norm around 2011, while most catalogs list the E-Series van with chip keys only from 2008. NXP Hitag Pro arrived with the 2013 Fusion, reached the F-150 for 2015 and now covers nearly the whole lineup. Remote-head keys appeared in the mid-2000s, Intelligent Access push-button fobs around 2010, and long-range 902 MHz fobs came with remote start. Recent models use 434 MHz fobs, and the Mustang Mach-E and F-150 Lightning added Phone As A Key.

• This smart fob, FCC ID M3N-A2C93142300, takes a CR2450 battery, not the CR2032 used in the earlier fob.
• The emergency blade in these fobs is Ford part 164-R8168, cut to the same HU101 profile as the door lock.

Programming a 2019 Fusion key

Smart fobs are added through the OBD-II port with a programmer that supports Ford's PATS security access, and we then cut the emergency blade on a laser-style machine. The same tool handles the 2017 flip key. With every key gone, we gain entry and cut a blade, and an active alarm can call for an emulator or bypass cable before we program new fobs. Your ID and registration are checked before we start.

Spare fobs are routine; all-keys-lost on these push-button Fusions generally needs an emulator or bypass cable, which we confirm by VIN first.

Lost every key to your Fusion?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Ford Fusion, ask us directly and you'll get a plain answer.

Fusion key battery

Battery details for the 2019 Fusion: CR2450 (smart fob); CR2032 (flip key). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Fusion uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Fusion, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Fusion key

• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Ford system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ford key problems

• Ford fobs come in 315 MHz, 434 MHz and long-range 902 MHz versions, and two fobs that look identical may not be interchangeable. We match the FCC ID printed on your old fob, or decode the VIN, before ordering a replacement.
• Battery sizes changed over the years. Separate remotes, remote-head keys and flip keys mostly take a CR2032, while most Ford smart fobs from about 2017 on take a thicker CR2450. Inland Empire heat shortens either one, so read the old cell before buying.
• Two chip keys hanging side by side, or a metal gadget pressed against the key head, can confuse PATS. Ford's manuals warn about this, and a truck that starts once the extra keys come off the ring has a healthy key.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2019 Ford Fusion key?

Don't wait until the last key disappears. If your Ford Fusion is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.