2013 Fiat 500 Key Replacement

2013 500 key specs

Every US-market 500 from 2012 to 2019, Abarth included, left the factory with a three-button flip key: lock, unlock and hatch release, with the transponder and remote sharing one head. Parts catalogs most often pair FCC ID LTQF12AM433TX (also printed 2ADFTF12AM433TX) and the Delphi body computer with 2012 to 2017 cars, so on a 2018 or 2019 car read the ID on your own fob first. A buttonless SIP22 transponder key with an ID46 chip makes a low-cost spare; it starts the car and opens the driver's door but can't lock or unlock remotely. No US 500 offered push-button start.

What's specific to the 2013 500

The 2013 Fiat 500 is the second of 8 model years in the 500 Type 312 (Mexico-built) (2012–2019), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 13 years old, a 2013 Fiat 500 has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2013 Fiat 500

• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a Fiat 500, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your 2013 500 and which we don't.
• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Fiat 500 only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.

How the Fiat immobilizer works on the 500

Fiat returned to the US for the 2012 model year, and every Fiat sold here since has a transponder immobilizer that must recognize the key before the engine will keep running. The Mexican-built 500 and 500c use a Philips ID46 (Hitag 2) chip in a three-button flip key, paired with a Delphi-type body computer. The Serbian-built 500L uses the same chip family but a Magneti Marelli-type body computer, so its remote is not interchangeable with the 500's. The Italian-built 500X steps up to AES encryption: a Megamos AES chip in the early flip key and Hitag AES in the push-button smart key, which is the only style Fiat's owner's manuals describe from 2017 on. The 124 Spider is the outlier, built by Mazda in Hiroshima with a Mazda-designed smart key running at 315 MHz. The first-generation 500e shares the 500's turn-key setup, while the 2024 and newer 500e uses a newer Stellantis keyless system. On the 500, 500L and 500X, the mechanical blade is the SIP22 laser-cut profile. When the chip isn't recognized, the blade can still turn the ignition, but the immobilizer will not let the engine run.

• Fiat's 2012 owner's manual says new 500s ship with a code card listing the key code numbers, and that the first owner is given a four-digit PIN.
• Refurbished Delphi-type 500 flip keys marked LTQF12AM433TX are also sold for 2015 to 2019 Ram ProMaster City vans with the same body computer.
• If the body computer doesn't recognize the chip, the blade still turns the ignition but the immobilizer keeps the engine from running.
• Fiat ended US sales of the gas 500, 500c and Abarth after the 2019 model year.

Programming a 2013 500 key

Programming runs through the OBD-II port with a tool that carries Fiat USA immobilizer software. The tool needs the car's security PIN, which it can often read directly or which can be retrieved by VIN once ownership is confirmed. Aftermarket remote heads usually have to be pre-coded before the car will learn them. After the transponder is accepted, the remote buttons are paired in the same session. All-keys-lost follows the same path once we've cut a working blade from the door lock or by code.

Lost every key to your 500?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Fiat 500 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Fiat 500, ask us directly and you'll get a plain answer.

500 key battery

Most fobs for a 2013 Fiat 500 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your 500 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Fiat keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 500, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a 500 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your 500 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Fiat key problems

• Inexpensive online Fiat flip keys often arrive locked or uncoded. Many must be pre-coded on a key programmer before the car will learn them, so a key that won't program is often the wrong blank rather than a fault in the car.
• Used smart keys bought online for the 124 Spider or 500X are often already locked to another vehicle and can't be reprogrammed. Buy new, or ask us to check the FCC ID and part number before you order.
• A key that turns but won't start the engine usually means the immobilizer doesn't recognize its transponder: a damaged chip, a key programmed to another car, or a spare that lost its pairing. Reprogramming fixes it; the ignition is rarely at fault.

Tips from a mobile locksmith

• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2013 Fiat 500 key?

Don't wait until the last key disappears. If your Fiat 500 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.