2012 Fiat 500 Key Replacement

2012 500 key specs

Every US-market 500 from 2012 to 2019, Abarth included, left the factory with a three-button flip key: lock, unlock and hatch release, with the transponder and remote sharing one head. Parts catalogs most often pair FCC ID LTQF12AM433TX (also printed 2ADFTF12AM433TX) and the Delphi body computer with 2012 to 2017 cars, so on a 2018 or 2019 car read the ID on your own fob first. A buttonless SIP22 transponder key with an ID46 chip makes a low-cost spare; it starts the car and opens the driver's door but can't lock or unlock remotely. No US 500 offered push-button start.

What's specific to the 2012 500

2012 was the first model year of the 500 Type 312 (Mexico-built). Early-production cars sometimes use different part numbers than later ones, so for a 2012 Fiat 500 we confirm the exact key from the VIN or the old key's FCC ID before cutting anything.

At roughly 14 years old, a 2012 Fiat 500 has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2012 Fiat 500

• Flip (switchblade) key. The hinge is the weak point on most flip keys. The pivot pin loosens, the spring loses tension, the release button sticks, and eventually the blade either won't lock open or flops out on its own. Carrying the key half-open in a pocket speeds that wear along. If the electronics are healthy, a replacement shell with a new hinge and pin often brings a 2012 Fiat 500 flip key back to crisp action: we transfer the board and chip, move or recut the blade, and test every function. If the board has broken solder joints or water corrosion, we'll show you the damage and quote a new key instead.
• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Fiat 500 only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.

How the Fiat immobilizer works on the 500

• Fiat's 2012 owner's manual says new 500s ship with a code card listing the key code numbers, and that the first owner is given a four-digit PIN.
• Refurbished Delphi-type 500 flip keys marked LTQF12AM433TX are also sold for 2015 to 2019 Ram ProMaster City vans with the same body computer.
• If the body computer doesn't recognize the chip, the blade still turns the ignition but the immobilizer keeps the engine from running.
• Fiat ended US sales of the gas 500, 500c and Abarth after the 2019 model year.

Programming a 2012 500 key

Programming runs through the OBD-II port with a tool that carries Fiat USA immobilizer software. The tool needs the car's security PIN, which it can often read directly or which can be retrieved by VIN once ownership is confirmed. Aftermarket remote heads usually have to be pre-coded before the car will learn them. After the transponder is accepted, the remote buttons are paired in the same session. All-keys-lost follows the same path once we've cut a working blade from the door lock or by code.

Lost every key to your 500?

Losing every key is fixable on most Fiats, but it takes more than a cut blade. On the 500, 500c and 500L, we verify ownership, decode the SIP22 door lock or cut a blade from the key code, then connect to the OBD-II port, read or enter the security PIN and program a new flip key. If you kept the code card that came with a new car, it speeds up the cutting step. The 500X needs AES-capable equipment, and some push-button or late-model cars involve extra security procedures that we explain on the phone. The Mazda-built 124 Spider depends on tool coverage for its VIN, and the plate stamped with its key code number helps on the cutting side. For the 2024 and newer 500e, plan on a dealer-supplied fob. Have your ID and registration or title ready, and give us the VIN when you call so we can confirm the route before we drive out.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Fiat 500 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2012 Fiat 500 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

500 key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your 500 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Fiat keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Fiat system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a 500 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your 500 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Fiat system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Fiat key problems

• Buying the wrong remote is a frequent mistake. The 500 and 500c use Delphi-type remotes marked LTQF12AM433TX or 2ADFTF12AM433TX, while the 500L uses the Marelli-type 2ADPXTRF198. The blades match, but the buttons only work on the right car.
• Flip-key hinges on the 500 and 500L wear out over time. The blade stops locking open or swings loosely, often because the pivot pin has worked free. A new shell with the original circuit board moved over usually fixes it.
• Inexpensive online Fiat flip keys often arrive locked or uncoded. Many must be pre-coded on a key programmer before the car will learn them, so a key that won't program is often the wrong blank rather than a fault in the car.
• A key that turns but won't start the engine usually means the immobilizer doesn't recognize its transponder: a damaged chip, a key programmed to another car, or a spare that lost its pairing. Reprogramming fixes it; the ignition is rarely at fault.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2012 Fiat 500 key?

Don't wait until the last key disappears. If your Fiat 500 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.