2009 Chevrolet HHR Key Replacement

2009 HHR key specs

Every HHR uses a B111 Circle Plus key with a Philips 46 transponder in its head, often marked with a circled plus. A blade copy without a learned chip turns the cylinder but will not start the car. Keyless entry comes from a separate three-button fob listed under FCC ID KOBGT04A and shared with GM's minivans of the period, and cars with remote start use a version with extra buttons. SS and Panel models use the same key.

What's specific to the 2009 HHR

The 2009 Chevrolet HHR is the fourth of 6 model years in the HHR Delta platform (2006–2011), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2009 Chevrolet HHR is about 17 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

If a newly cut key turns the 2009 HHR's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2009 Chevrolet HHR

• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Chevrolet HHR, we'll explain which method fits and why.
• Key with separate remote fob. Separate remotes are easy to find online, which is exactly why they cause trouble. A listing can show the same shell as your Chevrolet HHR remote while hiding a different FCC ID, frequency or internal chip, and some used remotes are locked to the first vehicle they were paired with. We're glad to look at one you've already bought, and we'll tell you honestly whether it can be paired before charging you to try. If the remote side of your setup has become unreliable, it's also worth asking whether a fresh remote and a newly cut key, matched together, would cost less than chasing repairs on aging parts.

How the Chevrolet immobilizer works on the HHR

• GM's 2014 ignition switch recall covered 2006-2011 HHRs, and GM advised carrying only the ignition key until repairs were made.
• The HHR's three-button remote, FCC ID KOBGT04A, also fits the Uplander and other GM minivans of the time.
• The HHR and the 2006-2010 Cobalt share the B111 Circle Plus key family.

Programming a 2009 HHR key

We cut the B111 blade and program the chip through the OBD-II port, or use GM's on-board add if you already have recognized keys. With every key lost, the programmer or GM's 30-minute relearn registers new keys and the lost ones stop working. The remote is programmed separately with a tool. Before we start, it is worth confirming that the ignition recall work is complete on your VIN.

Lost every key to your HHR?

When every key is gone, the route depends on the system. On Passlock and PASS-Key II vehicles we cut a new key from the code or by decoding a lock, add the right resistor pellet where needed, and the vehicle starts with no programming. Circle Plus and HU100 transponder vehicles get a freshly cut key programmed over OBD-II, and GM's own 30-minute relearn also works on many of them, erasing the lost keys in the process. Proximity-fob models need a new fob, an emergency blade cut to the locks and a programmer, often with a long security wait. Global B models and the electric Blazer EV and Equinox EV may need online authorization or the dealer, and we tell you which before starting. Expect to show ID and proof of ownership first.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Chevrolet HHR requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2009 Chevrolet HHR we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

HHR key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your HHR uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chevrolet HHR keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Chevrolet system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an HHR key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your HHR came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Chevrolet system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chevrolet key problems

• GM's 2014 ignition switch recall covered the 2005-2010 Cobalt and 2006-2011 HHR because a heavy key ring could knock the switch out of RUN. If a VIN check shows the recall still open, carry only the ignition key until it is repaired.
• Push-button Chevrolets show a remote-not-detected style message when the fob battery runs low. The owner's manual shows a backup spot, usually in the console or cupholder area, where a weak fob can still be read to start the vehicle.
• On trucks, vans and sedans with a separate remote, the remote cannot start the engine. A new fob fixes the locks, but a no-start with a security message is a key or immobilizer problem, which owners often misread as a remote failure.
• Inland Empire heat is hard on fob batteries and on the plastic heads of older transponder keys. A cracked head can let the chip shift or fall out, which typically leaves you with a key that turns the ignition but will not start the engine.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2009 Chevrolet HHR key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your HHR in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.