2019 BMW i3 Key Replacement

2019 i3 key specs

Every i3 starts with a smart fob in the cabin and the Start/Stop button. The fob contains the remote buttons, an ID49 transponder and a slide-out emergency blade for the driver's door, and Comfort Access was available. The battery-electric i3, the range-extender REx version and the i3s added for 2018 all share the same key system. i3 fobs carry their own part numbers and trim, so we match a replacement to your VIN rather than borrowing one from a gasoline BMW.

What's specific to the 2019 i3

The 2019 BMW i3 is the sixth of 8 model years in the i3 I01 (first generation) (2014–2021), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2019 BMW i3 is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2019 BMW i3

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your BMW i3 I01 (first generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the BMW immobilizer works on the i3

BMW has changed its key technology roughly once a decade, so the build date tells us more about the job than the badge on the trunk. In 2000, the 3, 5 and 7 Series, the X5 and the Z3 all used the EWS immobilizer: a diamond-shaped remote key with a Philips ID44-family transponder, checked by an EWS module that trades a rolling code with the engine computer. The key blade is a two-track or four-track design depending on the model. The 2002 7 Series introduced the Car Access System (CAS), and over the next decade CAS2, CAS3 and CAS3+ spread across the lineup with a rectangular fob that slides into a dash slot before you press Start/Stop. F-series cars from 2009 dropped the slot for Hitag Pro (ID49) smart fobs, stored in a CAS4 module on the 5, 6 and 7 Series and X3, and in a front electronic module (FEM) or body domain controller (BDC) on the 2, 3 and 4 Series, X5 and i3. G-series models from 2016 kept the BDC idea and, from mid-2020 builds, added BMW Digital Key for phones. The newest electronics, found on the current 7 and 5 Series, the electric i models and several recent redesigns and facelifts, are still dealer territory for new keys.

• BMW stopped selling the i3 in the US after the 2021 model year, and the iX and i4 took its place in the US lineup.
• The i3s added for 2018 uses the same fob and body module as the standard car.
• A fob with a weak battery can still start the car when held at the backup spot shown in the owner's manual.

Programming a 2019 i3 key

The i3 stores its keys in the body domain controller, the same type of module used in F-series BMWs of these years. We usually remove it for a bench read, write the car's data to a new fob and finish learning it to the car, then test keyless start. All-keys-lost follows the same bench approach, though coverage depends on the module's software level, so we check the VIN before a fob is ordered.

Spare fobs are usually possible with bench work on the body module. All-keys-lost depends on software level, and some cars still need a BMW dealer.

Lost every key to your i3?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your BMW i3 can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your BMW i3, ask us directly and you'll get a plain answer.

i3 key battery

Most fobs for a 2019 BMW i3 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh replacement, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your i3 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the BMW keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the BMW system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an i3 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button BMW i3 is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common BMW key problems

• Used BMW fobs from online sellers are locked to the car they came from. Some can be professionally renewed and recoded, many cannot, so send us the part number and FCC ID before you buy one.
• On slot-key BMWs from roughly 2002 to 2013, a fob the dash won't accept or recognize points to either a failing key or a faulty slot. Trying your spare first tells you which side has the problem before parts are ordered.
• Installing a used engine computer or immobilizer module leaves a BMW that cranks but won't run. The two modules share a secret code, so the replacement has to be synchronized or adapted to the car first.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2019 BMW i3 key?

Need a key for your 2019 BMW i3? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.