2017 BMW i3 Key Replacement

2017 i3 key specs

Every i3 starts with a smart fob in the cabin and the Start/Stop button. The fob contains the remote buttons, an ID49 transponder and a slide-out emergency blade for the driver's door, and Comfort Access was available. The battery-electric i3, the range-extender REx version and the i3s added for 2018 all share the same key system. i3 fobs carry their own part numbers and trim, so we match a replacement to your VIN rather than borrowing one from a gasoline BMW.

What's specific to the 2017 i3

The 2017 BMW i3 is the fourth of 8 model years in the i3 I01 (first generation) (2014–2021), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 9 years old, a 2017 BMW i3 has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2017 i3 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2017 BMW i3

• Smart proximity key (push-to-start). A smart or proximity key lets a 2017 BMW i3 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the BMW immobilizer works on the i3

• BMW stopped selling the i3 in the US after the 2021 model year, and the iX and i4 took its place in the US lineup.
• The i3s added for 2018 uses the same fob and body module as the standard car.
• A fob with a weak battery can still start the car when held at the backup spot shown in the owner's manual.

Programming a 2017 i3 key

The i3 stores its keys in the body domain controller, the same type of module used in F-series BMWs of these years. We usually remove it for a bench read, write the car's data to a new fob and finish learning it to the car, then test keyless start. All-keys-lost follows the same bench approach, though coverage depends on the module's software level, so we check the VIN before a fob is ordered.

No BMW in this range lets an owner add a key from the driver's seat, so every new key or fob is written with professional equipment, and the car's era decides how. EWS cars usually need the module removed and read on a programmer. CAS2, CAS3 and early CAS4 cars can often be handled through the OBD-II port, while CAS3+ and CAS4+ modules running later BMW software are commonly read on the bench. FEM and BDC cars almost always mean taking the module out, backing up its data and preparing it before a key can be added, and all-keys-lost work also needs the engine computer's ISN. BMW fobs lock to the first car they are coded to, so a used fob only works if it can be professionally renewed. Bring every key you have, since some procedures rewrite the stored key list, and expect us to check your ID and registration before we start.

Spare fobs are usually possible with bench work on the body module. All-keys-lost depends on software level, and some cars still need a BMW dealer.

Lost every key to your i3?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your BMW i3 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your BMW i3, ask us directly and you'll get a plain answer.

i3 key battery

Most fobs for a 2017 BMW i3 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh replacement, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your i3 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the BMW keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the BMW system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an i3 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button BMW i3 is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the BMW system adds equipment time and labor to the job.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2017 BMW i3 key?

Need a key for your 2017 BMW i3? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.