2018 Audi S6 Key Replacement

2018 S6 key specs

The twin-turbo V8 C7 S6 has push-button start with a fob from the 4G0 959 754 family. The fob only needs to be inside the cabin to start. Advanced key, where fitted, adds keyless entry at every door handle. The emergency blade inside the fob opens the driver's door when the fob or the car's battery is dead. Check the label on your existing fob when ordering a spare.

What's specific to the 2018 S6

2018 was the final model year of the S6 C7 (Typ 4G), before the C8 (Typ 4K) arrived for 2020. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2018 Audi S6 matches a 2013. At roughly 8 years old, a 2018 Audi S6 has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2018 S6 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2018 Audi S6

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Audi S6 C7 (Typ 4G), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Audi immobilizer works on the S6

• There was no 2012 S6 in the US; the C7 S6 arrived for 2013.
• The S6 uses the same key family as the C7 A6, so a parts match depends on the fob type, not the badge.

Programming a 2018 S6 key

The C7 S6 uses the same BCM2-type comfort module as the A6, so a new key starts with reading that module, through OBD-II on some versions or with the module removed on others. All-keys-lost always takes the bench route. After learning the key we check the start button, remote buttons and keyless entry before handing it over.

Spares are usually doable; all-keys-lost requires removing and reading the comfort module, and some late units need the dealer.

Lost every key to your S6?

Losing every key to an Audi is often solvable, but the method depends on the era. On 2000s cars with ID48 flip keys, we read the immobilizer data from the instrument cluster, sometimes on the bench, then cut a new HU66 blade by code or by decoding the door lock. On 2008-2018 slot-start and push-button models, all-keys-lost usually means removing the comfort or entry-and-start module so its memory can be read directly, which takes time and care. On many 2017-and-later models, and on the newest platforms, a lost-all situation goes through the dealer, and the car may need to be towed there. In every case we confirm ownership with your ID and registration or title before starting, and we tell you which route your VIN points to before you pay for anything.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Audi S6 can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your S6 and your schedule.

S6 key battery

Most fobs for a 2018 Audi S6 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your S6 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Audi keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your S6, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an S6 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Audi S6 is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Audi key problems

• Slot-start Audis, meaning B8-generation A4, A5 and Q5 models without advanced key, can develop a worn ignition slot that won't read or release the fob. That is an ignition switch repair, not a key problem.
• Remotes on older Audis can lose sync after a battery change. Pressing a remote button and then unlocking the driver's door with the blade within about a minute often resyncs them; if not, the remote needs adapting with a scan tool.
• Flip keys from the 2000s wear out at the pivot, so the blade stops locking open or flops loose. A new shell with a fresh HU66 blade can usually take your original transponder and remote board, which avoids reprogramming the car.
• Used keys pulled from another Audi are usually locked to that car. Some comfort-module-era keys can be reset with special equipment, but many later keys cannot, so check with us before buying a used fob.

Tips from a mobile locksmith

• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2018 Audi S6 key?

The quickest route to a working key for a 2018 Audi S6 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.