Rekey Door Locks in Pomona: Which Doors, Which Locks

Rekey Door Locks in Pomona: what to expect

Each kind of door hardware hides its cylinder in a different spot, and that drives how long the job takes. A deadbolt is the simplest: two screws release the interior thumbturn and the exterior cylinder slides out. Knobs and levers use a small release catch, and the cylinder comes out of the knob body. On a handleset, the key almost always lives in the deadbolt section above the grip, while the thumb latch below has no cylinder at all. Older front doors with mortise locks use a threaded cylinder held by a set screw on the edge of the door, and that screw is sometimes buried under decades of paint. Rim cylinders, common on gate locks and some older back doors, come out from the inside with two long screws. French doors and many fiberglass entry doors with multipoint locks use euro profile cylinders, which we normally replace with a new cylinder keyed to match rather than re-pin. Patio sliders and storm doors are the wild cards: many use inexpensive wafer locks that can't be re-pinned, so we swap in a better lock or add a secondary one.

Work included on a typical visit

• Front door deadbolt rekeying. If the front door has a double-cylinder deadbolt, keyed on both sides, both faces get re-pinned to the same new key. While we're there, we'll mention the exit concern: building codes expect a required exit door to open from inside without a key. Many owners switch to a single-cylinder model and handle worries about glass panels another way.
• Garage entry and garage side doors. The door between the garage and the house matters more than people think. Many households leave the overhead door up while they're in the yard or driveway, which makes that inner door a front door in practice. We rekey its knob and deadbolt to the house key and check that the door still closes and latches on its own.
• Patio sliders and French doors. If your slider has never had a working key, you're in good company. Plenty of patio door cylinders in Pomona were never keyed in the first place, or the key disappeared years ago. We'll tell you whether that lock can be put on a key, and if it can't, how to keep the door secure with an inside lock and a charley bar.
• Kwikset SmartKey locks. Kwikset SmartKey locks can be rekeyed without taking the cylinder apart, using the current key and a small reset tool. It sounds easy, and with a good working key it usually is. Where it goes wrong is a worn key, a botched attempt, or a cylinder stuck partway through the reset. Those are situations we can sort out on-site.
• Matching a door to the key you already carry. You don't always need a brand-new key. If you're adding a lock, or one door was never on your house key, we can rekey that single lock to the key you already use, provided the keyway is compatible. We decode your key's cuts and pin the cylinder to match, so nothing else in the house has to change.

What's different about Pomona

Apartment door locks follow the lease. Renters should get the landlord's written approval before any door is rekeyed, and many leases require giving management a copy of the key. Landlords handling a turnover usually want the entry deadbolt and knob rekeyed while mailbox and common-area keys stay with management. We'll rekey door locks inside the unit, cut keys for both tenant and owner, and note the change for your records.

Inland summer heat is hard on doors and locks. Doors facing south or west expand, dark-painted doors get hot enough to make hardware stiff, and old lubricant dries into grit. When we rekey door locks in hot areas, we clean each cylinder thoroughly, use a dry lubricant that won't gum up, and check that the bolt still throws when the door is warm, not just in the cool morning.

Older homes in Pomona often have a front door lock older than anyone living there: a mortise lock with a painted-over set screw, a rim lock on the back door, or knobs in keyways that few shops still stock blanks for. Most of these can be re-pinned if the lock body is sound. Where a part is obsolete, we'll offer a replacement cylinder or modern hardware keyed to match, and explain plainly why that door needs it.

Example situations

• Consider a back door deadbolt that only throws if you pull the door toward you first. The owner has done that for years and figures a rekey will cure it. With the cylinder out, though, the bolt still binds against the strike, which proves the lock isn't the problem. The fix is a strike adjustment and longer screws during the same visit, and afterward the new key turns with a fingertip.
• For example, a homeowner realizes the steel security screen door has a key nobody has seen in a decade, so the screen just stays unlocked. We'd pick or decode the screen door cylinder, then check whether it accepts the house keyway. If it does, it gets re-pinned to the house key. If it's a proprietary cylinder, we'd quote a compatible replacement before doing anything else.
• A typical evening call in Pomona: the door from the garage into the kitchen won't latch unless someone slams it. The owner wanted that lock rekeyed after a house sitter left and assumed the knob was failing. It isn't. The spring hinges have lost tension and the strike sits slightly high. We'd re-pin the knob and deadbolt, tension the hinges and reset the strike, and the door closes on its own again.
• For example, a homeowner off Garey Avenue asks us to rekey door locks including the patio slider, whose key went missing years ago. On inspection, the slider's cylinder is a wafer design that can't be re-pinned. Rather than charging for a pointless attempt, we'd show them why, then offer a keyed replacement that fits the slider's cutout or a sturdy foot lock that secures it from inside.

How the visit works

1. Tell us which doors and what's on them. A quick photo of each lock helps more than any description. Send pictures of the outside face of each knob, deadbolt or handleset and of the keys you use now. From those we can usually identify the brand, keyway and cylinder type and give you a much tighter quote over the phone.
2. Confirm you're authorized. Renters, property managers and relatives house-sitting each need slightly different proof. A tenant may need the landlord's written permission, depending on the lease. A manager shows written authorization from the owner. If you're unsure what counts, ask when you call, and we'll tell you exactly what to have ready.
3. Check each door before touching the lock. This is also when we confirm which locks can be rekeyed and which can't. A cheap slider cylinder, a worn-out knob or a proprietary smart lock cylinder gets flagged now, with options and prices, so nothing changes once we're halfway through the house.
4. Re-pin each cylinder, one door at a time. We work one door at a time so the house stays secure. The cylinder comes out, the plug is pushed out with a follower so the springs and driver pins stay put, and new key pins are set to the new key's cuts. Old pins are discarded, not reused.
5. Test from both sides. Keys cut in the van get deburred and tried in every lock they're meant to open. If a key feels rough or catches, we recut it. Testing every key in every intended door is tedious, and it's exactly the step that prevents a callback later.
6. Hand over keys and a door list. Keep a record of the new key code somewhere safe; it lets a locksmith cut accurate keys later instead of copying a worn copy. Either way, the new keys should go only to people you'd trust with your front door, which is the whole reason for the rekey.

Pricing factors

• What kind of hardware each door has. Standard deadbolts, knobs and levers are the quickest to rekey. Mortise locks, handlesets with two keyed functions, euro cylinders on multipoint doors and retrofit smart locks take longer to reach, and some need a replacement cylinder rather than a re-pin. Each of those is priced on its own line.
• Brands and keyways. High-security cylinders such as Medeco, Mul-T-Lock or ASSA often use restricted keyways with controlled key blanks. Rekeying those may require parts or keys sourced through an authorized dealer, which affects both price and timing. We'll tell you up front if any of your locks fall into that group.
• Door adjustments and small parts. Adjusting a strike plate, adding longer screws or tightening loose hinges adds a little time and occasionally a part, such as a reinforced strike. These fixes often matter as much as the rekey itself, because a door that binds will wear out a freshly pinned cylinder.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Pomona.

Practical tips before you call

• Hold on to the key code or the first key we cut. Copies made from copies drift a little each time, and eventually a duplicate won't turn smoothly. A key cut to the code is accurate, so treat it as your master copy and make future duplicates from it.
• Skip the spray oil before we arrive. Household lubricants leave a film that collects dust in the pins, and a cylinder soaked in oil is messier to re-pin. If a lock is stiff, leave it alone; we'll clean it properly and finish with a dry lubricant made for locks.
• Hand new keys to fewer people than before. A rekey is a reset; if the same five people end up with copies, you've changed the key but not who can get in. For occasional helpers, a smart lock code you can delete later is often better than another metal key.
• Pay attention to how the garage-to-house door closes while we're there. If it doesn't close and latch on its own, mention it. A properly tensioned spring hinge or closer keeps that door secure without anyone having to remember to pull it shut on the way out.

Mistakes to avoid

• Hiring whoever answers first from an online listing without checking for a license. California requires locksmith companies to be licensed through BSIS. Ours is LCO7891, and you can confirm it at search.dca.ca.gov. A legitimate locksmith also gives you a price before touching any door.
• Buying a DIY rekey kit for the wrong brand. Kits are keyway-specific, and the pins, springs and follower in a Kwikset kit won't help with a Schlage cylinder. Even with the right kit, one slipped follower can launch drivers and springs across the floor and leave the door unusable.
• Lubricating with oil or grease. A shot of household oil seems to help for a week, then the film gathers dust and the pins start to drag. Locksmiths use dry graphite or a PTFE lock lubricant, applied sparingly. Inside a cylinder, more lubricant is never better.

Getting to Pomona

Pomona is about 32 miles from our San Bernardino base, roughly 38 minutes in light traffic via University Parkway to SR-210 West. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Homes and businesses just off Phillips Ranch Road are routine stops for us. Give the suite or unit number and any gate instructions, and say whether the van can park out front or should pull into a side lot.

About Pomona: The Pomona Mall, designed by Millard Sheets and completed in 1962, turned nine downtown blocks into a pedestrian mall whose eastern end is now part of the Western University of Health Sciences campus.

Planning a rekey in Pomona?

Call (951) 903-3193 and tell us how many doors you want on the new key and the brand of the locks if you know it. We'll quote the rekey before any work starts.