Electric Strike Installation in Mentone

What to know first in Mentone

Strikes aren't universal, and compatibility is where most electric strike installation problems begin. A cylindrical lock, the knob or lever set found on most office doors, uses a rectangular strike at a standard 4-7/8 inch height. A mortise lock has a deeper, differently shaped latch and often a deadlatch that needs its own strike. Narrow-stile aluminum storefront doors usually carry a deadlatch or hookbolt that calls for a strike built for thin frames. Panic hardware with a rim device latch takes yet another type. Beyond the latch, we look at the frame: pressed steel with a reinforced pocket, a wood jamb, or an aluminum extrusion with almost no wall to work with. The backset, the distance from the door edge to the lock center, and the gap between door and frame decide whether the keeper can release freely. Sometimes the answer is a different strike; occasionally it's a different lock. We would rather tell you that at the first visit than after the frame is cut.

What we can do on-site

• Fail-secure strike installation. Most Mentone offices, shops and suites end up with fail-secure hardware. The door stays latched through outages and power-supply failures, so a dead battery can't turn the entrance into an open door. Inside, the lever still works. Outside, a card, button or key still gets in. We wire it, adjust the keeper and test it.
• Strikes for mortise locks and deadlatches. Older commercial and historic buildings in Mentone often have mortise locks worth keeping. A properly chosen strike lets you keep the original lock, key and trim while adding a remote release. It is more precise work than a cylindrical lock, because the latchbolt, the deadlatch plunger and the keeper must all line up.
• Frame cutting in hollow metal and wood. Pressed-steel frames accept a strike with a precise cutout and a clean back-box, usually after we check what's behind the jamb. Wood frames get routed to the template. We use jigs and templates so the opening matches the strike body, vacuum the debris, and touch up exposed metal so it doesn't rust.
• Fire-rated frames and listed strikes. Rated doors must latch in a fire, which generally means fail-secure hardware that's listed for the rating. Corridor doors and stair enclosures in Mentone office buildings are the usual examples. We check the label on the hinge edge or frame, match the strike to the listing and stay inside the manufacturer's limits.
• Buzz-in with intercom, video doorbell or desk button. The simplest electric strike installation pairs the strike with a momentary push button at the front desk. Add an intercom or video doorbell with a dry relay output and visitors announce themselves first. We match the doorbell's relay to the strike's voltage so one device can trigger the other without a power mishap.

How Mentone shapes the job

Older homes in Mentone often have wood jambs, thick paint and plaster that cracks if you look at it. A strike on a home office, a guest unit or a side entry is possible, but the wood needs gentle routing and the old latch may need replacing. We repair the jamb, touch up the paint, and tell you honestly when a smart lock would suit a residence better than a strike.

Schools, childcare centers, churches and youth programs in family neighborhoods use strikes to control who enters during the day while keeping exits free. A staff member sees a visitor on camera and releases the door. Parents should never meet a propped door, and children must always be able to leave. We emphasize fail-secure operation, short release times and clear instructions for substitute staff.

Inland heat is hard on electronics and hardware. Power supplies in a hot ceiling or an unventilated closet age faster, adhesive labels let go, and a door that swells in afternoon sun can start to bind on its latch, which shows up as a strike that will not release. We mount supplies where air moves, leave tolerance for seasonal movement and recheck alignment after the first hot spell.

Common situations

• Here is a residential example: a homeowner has converted a detached garage into an office and wants to admit clients without handing out keys or walking out each time. The wood jamb has decades of paint on it. We'd rout a clean pocket, fit a small fail-secure strike, run low-voltage wire back to a button inside the main house, and repair and repaint the jamb so the work disappears.
• Another common callback follows a gusty Santa Ana afternoon: the strike clicks, but the door will not open. Wind pressure and a strong closer are pushing the door hard against the latch, so the keeper cannot let go. We'd ease the closer, check the hinges and stop, readjust the keeper, and then retest the release with the building's air handlers running.
• In a building of salon suites, the rear door gets propped open because tenants and clients lose keys constantly. A reader with a fob for each stylist, a fail-secure strike and a door-position switch would change that. If the door stays open too long, the system chirps, and the owner can pull a record of which fob opened it and when.
• Suppose a tax-preparation office installed a fail-safe strike on its front door because someone called it the safe choice. During a utility shutoff in high-wind fire weather, the door would sit unlatched overnight. The fix is simple: swap in a fail-secure strike so the door stays locked through any outage, and add a small battery backup for the reader.

From your call to the finished job

1. Look at the door and the latch. On site we look at what you have: the latch, the strike plate, the frame, the gap, the closer and where power could come from. Photos help over the phone, but a walk-through spots the sagging hinge or the hidden reinforcement that pictures miss.
2. Choose the strike and approve the quote. We recommend a strike model, a failure mode and a release method, then write a quote covering hardware, frame work, wiring and testing. If part of the job belongs to an electrician or fire alarm contractor, the quote names that part. Nothing is cut until you approve.
3. Prepare the frame. Frame prep varies with the material. Steel is cut and filed, aluminum may get a reinforcing plate, and wood is chiseled and routed. In every case we protect the finish around the opening, keep debris out of the latch area and dry-fit the strike before wiring anything.
4. Run the wiring and set up power. We tie the strike into whatever opens it: a desk button, a doorbell relay, a reader's controller or a keypad. Keeping the release signal separate from the power feed makes troubleshooting simple, and a short note inside the panel records what goes where.
5. Mount and align the strike. The strike is fastened in its pocket and the keeper adjusted so the latch enters freely, rests without rattling and leaves without catching. We close the door slowly and slammed, with the closer working and with it disconnected, and tune until the strike behaves under both.
6. Test, demonstrate and hand over. Handover includes a demonstration, a written summary of settings, and any keys, cards or codes we programmed. We ask you to try the door yourself, because the person using it every day will notice things we won't. A follow-up call is welcome if anything feels off.

Pricing factors

• Frame material and condition. What sits behind the jamb matters: grout, studs, existing conduit or nothing at all. We can't know until the old strike comes out, so our quote notes the likely scenarios and we stop to requote before doing anything that costs more than we discussed.
• Wire distance and route. A short run through an accessible ceiling is quick. A long run through finished walls, concrete or several floors takes much longer, and may need an electrician or low-voltage contractor. We trace the route during the survey and show the cable work as its own line in the quote.
• Release method and add-ons. A desk button is the simplest release. A keypad costs more, a card reader and controller more again, and a networked system with software more still. Add-ons such as a door-position switch, exit sensor or intercom relay each appear on the quote, so you can add or skip them.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Mentone.

Mistakes to avoid

• Cutting the pocket too big. A loose, oversized opening weakens the frame, lets the strike rock and looks sloppy. Fixing it takes filler, a plate or a new section of frame. Cutting small to the manufacturer's template and widening only as needed beats the reverse.
• Leaving a plain spring latch exposed. If the lock has no anti-shim guard, someone can slide a card between door and frame and push the latch back, strike or no strike. A deadlatching lock or a guard plate closes that gap and is worth adding.
• Powering the strike from an undersized or shared supply. Too little current, or voltage lost along a long thin wire, makes the strike click without releasing, then work again unpredictably. Faults like that are hard to diagnose, and a properly sized supply and wire prevent them.

Practical tips before you call

• Plan the install before paint or flooring is finished. Cutting a freshly painted frame leaves touch-up scars, and rough-in before drywall is easier still. If a remodel in Mentone is underway, tell the contractor the door will get a strike so power reaches the frame at the right stage.
• Keep your keyed lock. With a fail-secure strike, the key still operates the lock from outside, so a dead power supply or an unplugged adapter never locks you out. Don't let anyone talk you into removing the cylinder just to save a step.
• Give the strike its own power supply, or a clearly rated output on a shared one. A leftover wall adapter is a common reason for buzzing and sticking. Check that the voltage on the strike's label matches the supply, because 12 and 24 volts are not interchangeable.
• Ask for a door-position switch if your door tends to get propped open. A door left ajar triggers a chirp or an alert, which stops a strike door from becoming an unlocked door by habit. The sensor is a small cost next to the equipment it protects.

Reaching Mentone

Mentone is about 20 miles from our San Bernardino base, roughly 27 minutes in light traffic via I-215 South to SR-210 East through Highland, exit San Bernardino Avenue in Redlands. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Rush hour on SR-210 can stretch a drive considerably. We'd rather give you a realistic arrival window than an optimistic one, and we'll call you if a closure or a crash changes the plan.

About Mentone: Mentone takes its name from Menton on the French Riviera, and the Mentone Corporation, formed in 1886, bought about 3,000 acres on the south bank of the Santa Ana River.

Business lock or door work in Mentone?

Call (951) 903-3193 with the address, the doors or hardware involved and when the site is open. We'll quote the job before any work starts and book a time within our hours that suits your schedule.