Replacing the Locks on Your Highland Home

Residential Lock Replacement in Highland: what to expect

Most modern residential doors are bored to a common pattern, and replacement locks are built around it. The main hole through the face of the door, called the cross bore, is 2-1/8 inches across. A 1-inch hole in the edge holds the latch or bolt. The backset, measured from the door's edge to the center of the main hole, is usually 2-3/8 inches on interior and older doors and 2-3/4 inches on many entry doors, and most current locks have adjustable latches for both. Exterior doors are typically 1-3/4 inches thick and interior doors 1-3/8, while thicker custom doors need extension kits. Then come the details that trip people up: the shape of the latch faceplate (drive-in, square corner or round corner), the distance between the knob and deadbolt holes, and, on handlesets, the spacing of the grip's mounting holes. Older doors may predate these standards entirely. We measure every one of those dimensions before recommending hardware, so the new lock fills the existing prep instead of leaving gaps or needing fresh holes.

What we can do on-site

• Knob and lever entry set replacement. Swapping a knob for a lever, or one brand for another, usually reuses the existing holes when backset and bore match. We confirm the latch length, check the faceplate shape against the old mortise, and replace the strike if the new latch needs a different opening. The finished door should close softly and latch the first time.
• Mortise lock replacement and conversion. Mortise locks vary in case size, backset and faceplate length, especially on doors built before the 1950s. We measure the pocket, the trim holes and the spindle position before ordering. A close match keeps your door's original look; a conversion plate is the fallback when no current mortise body fits the pocket without major cutting.
• Replacing a deadbolt with a smart or keypad lock. Retrofit-style smart locks such as August replace only the interior side of an existing deadbolt and keep your outside key. Full replacement units swap the whole deadbolt, keypad included. We help you choose based on whether you want codes at the door, whether the exterior faces hard afternoon sun, and how the lock behaves when batteries run low.
• Patio and French door hardware replacement. Sliding door handle sets and mortise latches are specific to the door's manufacturer and frame profile. When the latch or handle is broken beyond repair, we identify the door, match the replacement latch and handle, and fit a keyed version if you want to lock the slider from outside. A secondary foot lock is an inexpensive addition.
• Replacement after forced entry. Insurance claims tend to go more smoothly with clear documentation. We photograph the damaged hardware before removal, list what we replaced and note the grade of the new locks. If police took a report, keep the report number with our invoice. We verify ownership or residence before replacing locks after any break-in.

What's different about Highland

Foothill homes deal with dust, wind and fire-season evacuations. Replacement hardware there should hold up to grit, lock quickly when you're leaving in a hurry and be easy for everyone in the household to operate. We often install single-cylinder deadbolts with easy thumb-turns and recommend keeping a working physical key for every smart lock, since power and internet can drop during wildfire events.

HOAs sometimes regulate exterior appearance, including the finish or style of hardware visible from the street. Before replacing a front handleset or entry lock, check your community's architectural guidelines, since some require approval, and we can provide product details for the application. Locks on shared gates and amenity doors belong to the association, so replacing those goes through the HOA or its management company.

Older homes in Highland often have doors bored for hardware that no longer exists, mortise pockets, or several generations of patched holes. Residential lock replacement there starts with careful measuring and sometimes conversion plates or wood repair. We try to keep the door itself, since solid older doors are worth saving, and choose replacement hardware that fits the period look while adding a modern deadbolt.

Common situations

• Imagine a host renting out a backyard casita as a short-term rental who's tired of meeting guests to hand over keys. We replace the casita's keyed deadbolt with a keypad deadbolt that supports unique guest codes, key its backup cylinder separately from the main house, and show the host how to delete codes after each stay. The main house remains on its own key.
• Picture a front door after an attempted break-in: the deadbolt cylinder was wrenched until the housing cracked, though the door held. The owners want stronger hardware. We remove the damaged deadbolt, install a Grade 1 model with a reinforced strike and long screws, add an edge wrap around the lock area, and rekey the other exterior locks so the whole house shares one new key.
• In a 1930s Spanish-style house, for example, the front door's original mortise lock has a cracked case that can't be rebuilt, and no current mortise body matches the pocket. We fit a conversion plate that covers the old pocket, install a bored entry set and deadbolt in an oil-rubbed bronze finish that suits the house, and hand the original parts back to the owners.
• A homeowner buys a deadbolt and lever combo at a big-box store, then stops halfway because the latch won't line up and the deadbolt hits the old strike. The door has a 2-3/4-inch backset and radius-corner faceplate pockets. We set the adjustable latch correctly, chisel the pockets to fit, replace both strikes and finish the installation with the homeowner's own hardware.

Step by step with Julian's Locksmith

1. Inventory and goals. We start with a list: front, back, side and garage-entry doors, sliders, French doors, screen doors and any interior locks you want changed. For each, we note what's there now and what you want it to become. A clear list keeps the quote accurate and makes sure the right hardware is on the van.
2. Measure the door prep. At the house, we measure each door before recommending hardware: backset, cross-bore and edge-bore size, door thickness, faceplate shape, the spacing between knob and deadbolt holes, and handleset mounting holes. Those numbers decide which replacement locks fit cleanly and which would need new drilling.
3. Choose the hardware. With measurements in hand, we recommend specific hardware for each door: grade, style, finish and keyway. We carry common residential models and can order others. If you've already bought locks, we check them against the door prep and tell you honestly whether they'll fit and how they'll hold up.
4. Quote, approval and verification. You get an itemized quote: hardware for each door, labor, any strike or frame work, and keying. Nothing starts until you approve it. Because we're changing locks, we confirm you own the home or have the owner's authorization; tenants need written landlord approval unless state law gives them a specific right to change locks.
5. Remove and install. We remove the old hardware, clean and square the bore and edge holes, fit new latches and bolts to the faceplate pockets, and install the locks to the manufacturer's specifications. Strikes go in with long screws into the framing. Each door stays lockable throughout, so the house is never left open between steps.
6. Key, test and hand over. Before we leave, we walk through each door with you: how the locks work, how to change smart lock codes, which lubricant to use and when to tighten trim. Any door we noticed with problems beyond the lock, such as a sagging hinge or worn weatherstrip, gets mentioned too.

What affects the cost

• Hardware grade and brand. Within the same grade, prices vary with finish, style and features like SmartKey rekeying, pick-resistant cylinders or keypads. We quote hardware separately from labor, so you can compare options side by side and decide where an upgrade is actually worth it for your home.
• Fit and door preparation. If the new hardware fits the existing holes, installation is straightforward. Doors that need a new bore, a larger edge hole, a re-chiseled faceplate pocket or filled holes from old hardware take more time. Measuring first keeps those surprises to a minimum and lets us quote accurately from the start.
• Who supplies the hardware. You can buy locks yourself and pay only for installation, or have us supply them. Supplying your own can save on hardware, but returns and fit problems become your errand. When we supply the hardware, we're responsible for it fitting the door and keying correctly.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Highland.

Advice before you book

• After the replacement, put a little dry lubricant in each new cylinder a few times a year and tighten trim screws when they loosen. New hardware stays smooth longer with light care, especially on doors facing afternoon sun, wind-blown dust or sprinkler overspray.
• If you're replacing a deadbolt next to a glass sidelight, think through egress before choosing a double-cylinder lock. A single-cylinder deadbolt combined with laminated glass or security film on the sidelight usually solves the reach-through concern without needing a key to get out in an emergency.
• Ask for the old strike to be replaced along with the lock. A new deadbolt sliding into an old, thin strike plate held by short screws gives up much of its strength. A heavy-duty strike with screws reaching the framing makes the frame, not just the lock, part of the defense.
• Photograph your current handleset and both sides of the door before shopping, and measure the distance between the grip's mounting holes. Bring those to us or to the store. Matching the hole spacing avoids drilling new holes and leaving old ones exposed on the face of your front door.

Mistakes to avoid

• Mixing brands with different keyways across the house. It looks fine on installation day, then you're carrying three keys and can't key them alike later without replacing cylinders. Choose one keyway family for every keyed lock before you start buying hardware.
• Letting a tenant or contractor replace locks without the owner getting keys or records. Owners end up locked out of their own property, or unsure who holds keys. Whoever does the replacement, make sure the owner receives keys and a note of brand, keyway and key count for every lock.
• Over-tightening the through-bolts on new hardware. Cranking the screws distorts the chassis, binds the latch and can crack a die-cast housing before the lock is a week old. Trim screws should be snug, with the knob or lever still returning freely afterward.

Getting to Highland

Highland is about 11 miles from our San Bernardino base, roughly 18 minutes in light traffic via University Parkway to I-215 South. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Our path into Highland depends on where the previous job wrapped up. Sometimes that's a straight run via Victoria Avenue; other times it's surface streets the whole way. Either way, you get a heads-up call when the technician is close.

About Highland: The 2020 census counted 56,999 Highland residents, up from 53,104 in 2010 and 34,439 in 1990.

Home lock work in Highland?

Call (951) 903-3193 with the address and a quick description of the doors and locks involved. We'll quote the job before any work starts.