2024 Volvo S60 Key Replacement

2024 S60 key specs

The 2019-2024 S60 uses Volvo's SPA remote key, a fob with lock, unlock, trunk and panic buttons and a detachable emergency blade. You start the car by turning the start knob on the center console with the fob anywhere inside. Keyless entry by touching the door handles depends on trim and package. Recharge T8 plug-in hybrids and Polestar Engineered sedans use the same key family. If the fob battery fails, the car can still be started by placing the fob in the backup reader position in the console.

What's specific to the 2024 S60

The 2024 Volvo S60 is the sixth of 7 model years in the S60 Third generation (SPA) (2019–2025), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At 2 years old, a 2024 Volvo S60 is usually still on its original keys and fob batteries. The most common call for a car this new is a second key, since many buyers leave the dealer with only one, or a replacement after a lost fob.

Smart-key cars like the 2024 S60 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2024 Volvo S60

• Smart proximity key (push-to-start). A smart or proximity key lets a 2024 Volvo S60 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Volvo immobilizer works on the S60

• US S60 production ran at Volvo's Ridgeville, South Carolina plant from September 2018 until June 2024, and 2025 was the final US model year.
• The emergency blade keeps the HU101 profile of earlier Volvos, but the fob electronics are a newer, encrypted generation.
• Volvo's Care Key, introduced with the 2021 model year, lets an owner set a top-speed limit for a key lent to another driver.

Programming a 2024 S60 key

SPA fobs are registered through the car's central module with security access that Volvo controls tightly. Aftermarket equipment can add a fob to some of these sedans, sometimes with the CEM removed and read on the bench, depending on model year and software level, and we check your VIN before promising anything. Newer sedans often need a dealer key programmed with Volvo's online system; we can still open the car, cut the emergency blade, and help arrange the rest.

Spares and all-keys-lost depend on year and software level; newer cars usually go through a Volvo dealer.

Lost every key to your S60?

Losing every key to a Volvo is solvable on most older models, and the method depends on the platform. On P1 and P2 cars, we pick or decode a door lock to cut a blade, read the CEM PIN, and program new keys, normally at least two, so a lost key can no longer start the car. P3 cars from 2007 to 2018 often need the CEM removed and read on the bench before new fobs can be registered, and some late examples end up at the dealer. On SPA vehicles from 2016 on, some 2016-2021 cars can be done the same bench way, but newer ones, and the electric EX30, EX40 and EX90, usually mean a dealer key ordered by VIN. Even then, we can get you into the car, cut the emergency blade where there is one, and help coordinate. Expect us to check ID and proof of ownership before any work begins.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Volvo S60 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2024 Volvo S60 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

S60 key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your S60 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your S60, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an S60 key

• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Volvo system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Volvo key problems

• On 2001-2007 P2 cars, the CEM itself can fail, with cracked solder joints or failing internal relays causing a no-crank or odd electrical faults. It can look like a bad key, but no new key will help until the module is repaired.
• P3 fobs from 2007 to 2018 run on a CR2430 cell. When it weakens, Keyless Drive and the remote buttons fail first, but pushing the fob fully into the dash slot usually still starts the car because the slot reads the transponder directly.
• Inland Empire heat shortens coin-cell life in every Volvo fob. Most newer Volvos show a low remote-key battery message on the dash, and replacing the cell when it appears beats having the fob quit in a parking lot.
• Remote starters installed on CEM-based Volvos need a proper immobilizer interface. Installs that hide a spare key behind the dash weaken the car's security and can cause intermittent no-start faults that are hard to trace later.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2024 Volvo S60 key?

Don't wait until the last key disappears. If your Volvo S60 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.