2013 Suzuki Kizashi Key Replacement

2013 Kizashi key specs

The Kizashi uses Suzuki's four-button smart fob, listed under FCC ID KBRTS009 with lock, unlock, trunk and panic buttons and a 315 MHz transmitter. You keep the fob in a pocket or bag for entry and for the engine start button on the dash. A small emergency key slides out of the fob, listed by suppliers under part 37145-57L00, so you can open the driver's door when the fob battery is flat. Listings disagree on its blade profile, so we match it to your original. There is no separate transponder key.

What's specific to the 2013 Kizashi

2013 was the final model year of the Kizashi Single generation. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2013 Suzuki Kizashi matches a 2010. At roughly 13 years old, a 2013 Suzuki Kizashi has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2013 Kizashi can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2013 Suzuki Kizashi

• Smart proximity key (push-to-start). A smart or proximity key lets a 2013 Suzuki Kizashi open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Suzuki immobilizer works on the Kizashi

Suzuki sold cars in the US for only part of this period, with 2013 the last model year, and the key hardware comes from several different sources. The Suzuki-designed cars of 2000 to 2005, the Swift, Esteem, Vitara, Grand Vitara, XL-7 and Aerio, use conventional turn keys with separate keyless-entry remotes. Supplier catalogs show plain, chipless blanks for them, and we have not found a reliable record of a factory immobilizer on US cars of those years, so we check the key head and the dash before cutting. The 2006-2013 Grand Vitara and the 2007-2013 SX4 move to Philips ID46 transponder keys on the HU133R blade, with Suzuki's keyless start as an option on better-equipped trims. The 2010-2013 Kizashi has a smart fob and push-button start as standard. The rest of the lineup came from partners. GM Daewoo built the Forenza, Reno and Verona in South Korea, and their keys are plain mechanical keys without a chip. CAMI built the 2007-2009 XL7 with GM's Circle Plus key, and the Equator pickup is a Nissan Frontier with Nissan's ID46 key.

• Supplier listings pair the KBRTS009 fob with part number 37172-57L20 and a CR2032 cell, and most we found cover 2010-2012 cars, so a 2013 fob is confirmed by VIN.
• Used fobs must be unlocked or re-flashed before reuse, which is why a new or professionally reset fob is the cleaner choice.
• Push-button start was standard, so no Kizashi trim has a traditional ignition key.

Programming a 2013 Kizashi key

There is no on-board procedure for the KBRTS009 fob, so every key goes in through the OBD-II port with a programmer that completes Suzuki's security step. A new fob is the cleanest choice; a used one usually needs to be unlocked or re-flashed before the car will accept it. The emergency insert is cut separately, by code or by decoding the door lock. For all-keys-lost, we confirm tool coverage for your VIN before booking.

Fobs are programmed through OBD-II, but genuine KBRTS009 fobs are scarce now, so we confirm availability and coverage for your VIN before booking.

Lost every key to your Kizashi?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Suzuki Kizashi can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2013 Suzuki Kizashi we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Kizashi key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare CR2032 at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your Kizashi uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Suzuki Kizashi keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Kizashi, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Kizashi key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Kizashi came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Suzuki key problems

• Since Suzuki stopped selling cars in the US, key codes and genuine parts can take longer to track down. Decoding the door lock is often the fastest route to a first working key.
• Genuine Suzuki smart fobs, such as the KBRTS003 for keyless-start Grand Vitaras and SX4s and the KBRTS009 for the Kizashi, are increasingly sold as refurbished or aftermarket stock. A used fob can often be reused, but only after it is unlocked or re-flashed.
• Separate remotes on these Suzukis hold only a few fobs, and guides disagree on whether the limit is three or four. Pairing one past the limit erases the oldest, so program every remote you plan to keep in the same session.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2013 Suzuki Kizashi key?

The quickest route to a working key for a 2013 Suzuki Kizashi starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.