2020 Subaru WRX Key Replacement

2020 WRX key specs

From 2015 the WRX and STI became their own model, and most cars use a four-button remote-head key with a side-cut blade. Upper trims added Keyless Access with push-button start, using a smart fob with an emergency blade inside. Subaru's bulletin shows the 2015 smart key with a different emergency key from 2016 and later cars, and the 2020 remote-head key has a new part number, so check the part number on your old key.

What's specific to the 2020 WRX

The 2020 Subaru WRX is the sixth of 7 model years in the WRX VA (first standalone generation) (2015–2021), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2020 Subaru WRX is about 6 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2020 Subaru WRX

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2020 Subaru WRX with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Subaru WRX VA (first standalone generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Subaru immobilizer works on the WRX

• Subaru's bulletin lists the 2015 WRX and STI smart key with a 5+4 laser emergency key and a thinner 4+4 key from 2016.
• The 2015-2019 WRX remote-head key, FCC ID CWTWB1U811, is the same part used on several Imprezas and Foresters of the era.
• The STI used the same keys as the WRX of its year and ended US sales after 2021.

Programming a 2020 WRX key

With a working key, adding a remote-head key or Keyless Access fob is routine through the OBD-II port, and the remote is registered in the same pass. Smart fobs must be new or reset to blank. When every key is lost, remote-head cars are handled with Subaru's immobilizer data, while smart-key cars can need special tools or the dealer. 2020-2021 cars carry a new key part number, so we confirm the chip before ordering.

A Subaru built before its line got an immobilizer only needs a correctly cut key. We cut from the key code, which Subaru releases by VIN through its lock information service (a paid site for professional locksmiths), or by decoding a lock. Transponder Subarus from 2005 through the G-chip years are programmed through the OBD-II port, and Subaru's own procedure relies on an immobilizer security ID that is released along with the key code. Remote-head keys are normally registered as transmitters in the same session on 2012 and later cars, while the separate fobs of earlier years have their own routines. H-chip cars accept an added key readily when a working key is present, but all-keys-lost needs dedicated Subaru software, an emulator or bench work, and Keyless Access fobs must be new or reset to blank. Bring every key you still have, and expect us to check ID and registration first.

Spare keys are routine. All-keys-lost on remote-head cars is usually fine, but Keyless Access cars can need special tools or the dealer.

Lost every key to your WRX?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Subaru WRX, ask us directly and you'll get a plain answer.

WRX key battery

Battery details for the 2020 WRX: CR1620 (remote-head key); CR2032 (most smart fobs). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your WRX uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Subaru WRX keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a WRX key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2020 Subaru WRX key?

Don't wait until the last key disappears. If your Subaru WRX is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.