2016 Subaru Forester Key Replacement

2016 Forester key specs

The 2014 Forester brought a remote-head key with a side-cut blade and the 80-bit G chip, ending high-security keys on the model. Upper trims, notably the Touring, have Keyless Access with push-button start. Subaru's bulletin lists these smart keys from 2014, with a 5+4 inside-cut emergency key on 2014-2015 cars and a thinner 4+4 key from 2016. The emergency blades are different parts, so read the label on your fob before ordering.

What's specific to the 2016 Forester

The 2016 Subaru Forester is the third of 5 model years in the Forester SJ (fourth generation) (2014–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 10 years old, a 2016 Subaru Forester has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2016 Subaru Forester

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2016 Forester, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2016 Subaru Forester open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Subaru immobilizer works on the Forester

Subaru came to engine immobilizers later than most brands sold in the US, which keeps things simple for owners of early-2000s models: no 2000-2004 US Subaru has a transponder, so a correctly cut key starts the car. Subaru's own chart shows immobilizers arriving by model and trim from the 2005 model year. That year only the Forester XT, Impreza STi, Legacy GT and Outback XT and 3.0R had one. Every Legacy, Outback and Tribeca followed for 2006, the WRX joined the STi, the whole Impreza line had one by 2008 and the whole Forester line by 2009. The first systems use Texas 4D62 chips in side-cut keys. Subaru then moved to high-security laser-cut keys on 2008-2011 Imprezas, 2008-2014 WRX and STI models, 2009-2013 Foresters and 2010-2014 Legacy and Outback models. From the 2012 Impreza, an 80-bit Subaru G chip arrived in a side-cut remote-head key. The 2017 Impreza introduced the 128-bit Subaru H chip, which reached the Crosstrek for 2018, the Forester and Ascent for 2019 and the Legacy and Outback for 2020. Keyless Access smart keys began with the 2013 BRZ and the 2013-2014 Legacy and Outback.

• Subaru's bulletin notes the 2014 Forester smart key has an inside-cut emergency blade with a different part number and cut code from the 2013 BRZ's.
• Supplier listings show two remote-head FCC IDs for 2014-2018 Foresters, CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz.
• The HYQ14AHC smart key, part 88835-AL04A, takes a CR2032 battery and is listed for Foresters among Subarus of 2014-2017.

Programming a 2016 Forester key

Remote-head keys and smart fobs program through the OBD-II port, with the remote side handled in the same procedure when a working key is present. A smart fob must be new or reset before it will register. With every key lost, remote-head cars follow Subaru's immobilizer procedure and are usually fine, while smart-key cars can need special tools or the dealer. We cut the remote-head blade or the fob's emergency insert by code or by decoding your door lock.

Spare keys are routine. All-keys-lost on remote-head cars is usually fine, but Keyless Access cars can need special tools or the dealer.

Lost every key to your Forester?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Subaru Forester can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Subaru Forester requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Subaru Forester, ask us directly and you'll get a plain answer.

Forester key battery

Battery details for the 2016 Forester: CR1620 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Forester uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Subaru keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Forester, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a Forester key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Subaru system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Used Subaru fobs sold online can arrive already programmed to another car. Ask whether a fob is new or reset to a blank state before you buy, and bring the part number and FCC ID from your old key so we can confirm the fit before programming.
• Subaru remotes of one era were built on two frequencies under different FCC IDs: CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz. Both appear on remote-head keys for 2010-2015 Subarus, so match the part number printed on your old key before you buy a replacement.
• If a Keyless Access fob battery dies, the car can usually still be started with the backup method in the owner's manual, which uses the fob and the start button. The emergency blade hidden in the fob opens the driver's door.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2016 Subaru Forester key?

Need a key for your 2016 Subaru Forester? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.