2019 Subaru Crosstrek Key Replacement

2019 Crosstrek key specs

From 2018 the Crosstrek uses the 128-bit H chip. Lower trims generally have a four-button remote-head key with a side-cut blade, while the Limited and other upper trims have Keyless Access with push-button start. Remote-head keys changed from a black internal pod in 2018 to a gray one from 2019. Subaru's bulletin lists the remote-head key as part 57497FL000 for 2018 and SJ051 for 2019 through 2021.

What's specific to the 2019 Crosstrek

The 2019 Subaru Crosstrek is the second of 6 model years in the Crosstrek GT (second generation) (2018–2023), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2019 Subaru Crosstrek is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2019 Crosstrek can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2019 Subaru Crosstrek

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2019 Crosstrek, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2019 Subaru Crosstrek open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Subaru immobilizer works on the Crosstrek

Subaru came to engine immobilizers later than most brands sold in the US, which keeps things simple for owners of early-2000s models: no 2000-2004 US Subaru has a transponder, so a correctly cut key starts the car. Subaru's own chart shows immobilizers arriving by model and trim from the 2005 model year. That year only the Forester XT, Impreza STi, Legacy GT and Outback XT and 3.0R had one. Every Legacy, Outback and Tribeca followed for 2006, the WRX joined the STi, the whole Impreza line had one by 2008 and the whole Forester line by 2009. The first systems use Texas 4D62 chips in side-cut keys. Subaru then moved to high-security laser-cut keys on 2008-2011 Imprezas, 2008-2014 WRX and STI models, 2009-2013 Foresters and 2010-2014 Legacy and Outback models. From the 2012 Impreza, an 80-bit Subaru G chip arrived in a side-cut remote-head key. The 2017 Impreza introduced the 128-bit Subaru H chip, which reached the Crosstrek for 2018, the Forester and Ascent for 2019 and the Legacy and Outback for 2020. Keyless Access smart keys began with the 2013 BRZ and the 2013-2014 Legacy and Outback.

• Supplier listings show the black-pod CWTB1G077 remote-head key, part 57497-FL00A, for the 2018 Crosstrek.
• Subaru's bulletin lists Crosstrek remote-head key part 57497SJ051 for 2019 through 2021.
• Smart fobs with FCC ID HYQ14AHK operate at about 434 MHz and are listed for 2017-2020 Subarus, including the Crosstrek.

Programming a 2019 Crosstrek key

Adding a key with one working key present goes through the OBD-II port with current Subaru software. All-keys-lost is more involved: bladed H-chip keys in particular need dedicated Subaru software or an emulator, and some programmers don't support them at all. We look up your VIN and key type first, then tell you whether we can do it on site or whether a dealer visit makes more sense.

Spare keys are routine. All-keys-lost needs specialized Subaru software or emulators; some cars may need the dealer.

Lost every key to your Crosstrek?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Crosstrek and your schedule.

Crosstrek key battery

Battery details for the 2019 Crosstrek: CR1620 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Crosstrek uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Subaru Crosstrek keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Crosstrek key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Subaru remotes of one era were built on two frequencies under different FCC IDs: CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz. Both appear on remote-head keys for 2010-2015 Subarus, so match the part number printed on your old key before you buy a replacement.
• Remote-head keys from 2012 through at least 2022 mostly run on a CR1620 cell, while Keyless Access fobs from 2014 on take a CR2032. The 2024 remote-head key moved to a thicker CR2025. Inland Empire summer heat shortens coin-cell life, and shrinking range is the usual warning.
• Remote-head key shells tend to crack at the blade root after years on a heavy keyring. The remote board and transponder can usually be moved into a new shell with a freshly cut blade, which often costs less than a complete new key.

Tips from a mobile locksmith

• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2019 Subaru Crosstrek key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Crosstrek in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.