2016 Ram 4500 Key Replacement

2016 4500 key specs

Through 2018 the 4500 uses the Fobik, the bladeless remote that plugs into a slot in the dash. Trucks from 2011 and 2012 carry the IYZ-C01C family, and the 2013 update switched to fobs marked GQ4-53T, which are not interchangeable. Most fleet trucks have the basic three-button layout. If your cab has a dash start button instead of a key slot, tell us when you call, because it takes a proximity fob. The emergency insert opens the cab doors, but toolboxes, dump body controls and service compartments are keyed separately by the upfitter.

What's specific to the 2016 4500

The 2016 Ram 4500 is the sixth of 8 model years in the 4500 4th-generation chassis cab (2011–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 10 years old, a 2016 Ram 4500 has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2016 Ram 4500

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2016 Ram 4500 with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.

How the Ram immobilizer works on the 4500

Ram became a stand-alone brand for the 2011 model year, separating the pickups from Dodge, and the badge now also covers the C/V cargo van, the ProMaster vans and the 2011 Dakota. The full-size pickups of 2011 and 2012 start with a Fobik, a bladeless remote that plugs into an ignition node in the dash; the node reads a Philips ID46 transponder inside the fob before the engine is allowed to run. The 2013 update kept the Fobik on most trucks but moved to a new fob family, and Keyless Enter 'n Go, with a proximity fob and a start button, was available on many higher trims. The 1500 Classic carried that Fobik all the way to 2024. The redesigned 1500 and Heavy Duty trucks of 2019 switched to push-button smart keys with Hitag AES (4A) transponders, learned by a radio-frequency hub and shielded by a security gateway at the diagnostic port. The 2011 Dakota kept a traditional cut transponder key. The vans follow Fiat practice instead: the ProMaster and ProMaster City launched with SIP22 flip keys carrying an ID46 chip, and the full-size ProMaster moved to a push-button smart key for 2022.

• Fobs changed with the 2013 update, so a 2011-2012 fob will not program to a later chassis cab.
• Upfitter-installed body locks are separate from the truck key and can often be rekeyed or replaced on their own.
• Removing lost fobs from memory during programming stops them from starting the truck.

Programming a 2016 4500 key

The Fobik is programmed to the ignition node through the OBD-II port using the PIN, with the remote buttons learned at the same time. For fleets, we can program several fobs in one visit and remove any that are missing. All-keys-lost follows the same steps, so a truck that has lost its only fob on a job site can usually be put back to work where it sits.

Lost every key to your 4500?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Ram 4500 can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2016 Ram 4500 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

4500 key battery

Most fobs for a 2016 Ram 4500 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your 4500 uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Ram 4500 keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ram keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 4500, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a 4500 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Ram 4500 is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ram key problems

• Upfitted chassis cabs and work vans carry body, toolbox and compartment locks that are separate from the vehicle key. Those can usually be rekeyed or replaced on their own when a key ring goes missing from a fleet.
• A fob bought from a parts counter or online usually arrives with an uncut emergency key. Left uncut, it cannot open the door when the fob or the truck battery dies, so have it cut when the fob is programmed.
• Used Ram fobs sold online are locked to the truck they came from. They only program after being unlocked or re-flashed, and many never work at all, so a new or properly prepared fob is the safer purchase.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2016 Ram 4500 key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your 4500 in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.