2020 Ram 3500 Key Replacement

2020 3500 key specs

Ram 3500s from 2019 through 2024 use push-button start and a GQ4-76T smart key with an emergency blade inside. Fobs range from a basic three-button version to five-button keys with remote start and power tailgate on Laramie, Longhorn and Limited pickups. Chassis cabs use the same fob family, usually in the simpler layouts. Because the FCC ID is shared across the Heavy Duty line, the part number printed inside your fob is the best guide to an exact replacement.

What's specific to the 2020 3500

The 2020 Ram 3500 is the second of 6 model years in the 3500 5th generation (2019–2024), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2020 Ram 3500 is about 6 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2020 Ram 3500

• Smart proximity key (push-to-start). A smart or proximity key lets a 2020 Ram 3500 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Ram immobilizer works on the 3500

• The 3500's GQ4-76T smart key uses a CR2032 battery, unlike the 1500 DT fob's CR2450.
• One-ton chassis cabs share the pickup's key system, so service-body trucks are programmed the same way.
• A security gateway module blocks key programming over OBD-II until the tool is authorized.

Programming a 2020 3500 key

We program smart keys to the radio-frequency hub through the OBD-II port, getting past the security gateway with an authenticated session or a bypass cable. Spares with an existing key present are routine. For all-keys-lost, many trucks can still be done where they sit, but some need the RF hub removed for bench programming, and a few are dealer jobs. We check your VIN against current coverage before quoting.

Almost every Ram key job runs through the immobilizer PIN. On Fobik-era trucks and vans, professional tools can usually read it through the OBD-II port and add a fob in one session, which also pairs the lock, unlock and remote start buttons. Newer Rams add a security gateway module that blocks key programming at the diagnostic port until the tool is authenticated online or connected behind the gateway with a bypass cable. The 2019-and-later smart keys are learned by the radio-frequency hub, and the replacement has to match the FCC ID and part-number family of your original, which differ between the 1500 and the Heavy Duty trucks. The Fiat-derived ProMaster and ProMaster City flip keys need specialist equipment, because the remote's own memory has to be written before the van will learn it. Ram fobs are also not plug-and-play from an online marketplace: a used fob only programs after it has been unlocked or re-flashed.

Spares are routine. All-keys-lost may need RF hub bench work or the dealer on some trucks.

Lost every key to your 3500?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ram 3500 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2020 Ram 3500 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

3500 key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare CR2032 at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your 3500 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 3500, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a 3500 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your 3500 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2020 Ram 3500 key?

Don't wait until the last key disappears. If your Ram 3500 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.