2017 Nissan Versa Key Replacement

2017 Versa key specs

The second-generation Versa sedan arrived for 2012. Most of these cars use a conventional ignition with an ID46 remote head key, three or four buttons and FCC ID CWTWB1U751, or a plain chipped key on base cars without keyless entry. Some higher trims could have an Intelligent Key with push-button start. If you own a 2012 hatchback, it is still the first-generation design and uses those keys instead, and the Versa Note hatchback that joined for 2014 is listed on its own page.

What's specific to the 2017 Versa

The 2017 Nissan Versa is the sixth of 8 model years in the Versa N17 (second-generation sedan) (2012–2019), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 9 years old, a 2017 Nissan Versa has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2017 Versa can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2017 Nissan Versa

• Transponder (chip) key. A transponder key carries a small chip in its head, usually a glass capsule or a carbon wafer, with no battery of its own. When you turn the key in a 2017 Nissan Versa that uses one, an antenna ring around the ignition energizes the chip and asks for its code. If the answer matches what the immobilizer has stored, the engine is allowed to run. If it doesn't, you get the classic symptoms: the engine cranks but won't fire, or it fires and dies after a second, and the security light on the dash flashes or stays lit. That's why a perfectly cut copy without a programmed chip will open the doors but won't start the car.
• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2017 Versa, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan Versa N17 (second-generation sedan), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the Versa

• Supplier catalogs list a four-button remote head key with a transponder chip for Versas from 2012 through 2024.
• Supplier catalogs list the 2013-2016 four-button fob under FCC ID CWTWB1U815, which is also listed for the 2013-2015 Sentra.
• Supplier catalogs list the CWTWB1U751 remote head key in three- and four-button forms for Nissans through 2019, including the Versa.

Programming a 2017 Versa key

Remote head and plain chipped keys are cut by code or by decoding a lock, then registered through the OBD-II port with a PIN calculated from the security code. Intelligent Keys on equipped cars are registered the same way, and their metal key is cut to the door. Keys not present are erased, so bring them all. Spares and all-keys-lost are routine on these cars.

Nissan keys are registered through the OBD-II port under the dash. The car reports a security code from its body control module or immobilizer, and our programmer turns it into the four-digit PIN that opens key registration; many 2013-and-later cars present a longer 20-digit code that needs an online calculation. Registration wipes every key that is not in the car at that moment, so bring all the keys and fobs you want to keep, and Nissan's manuals allow four or five registered keys, depending on the car. On turn-key models from the early 2000s, the separate remote usually pairs through an on-board routine of ignition cycles and button presses, but the transponder key always needs a programmer. Replacement Intelligent Keys must match the original part number, and many newer AES fobs are locked to the first car that learns them. We check your ID and registration before any key work starts.

Lost every key to your Versa?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Nissan Versa, ask us directly and you'll get a plain answer.

Versa key battery

Battery details for the 2017 Versa: CR1620 (remote head key). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Versa uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Versa, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a Versa key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Nissan Versa is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2017 Nissan Versa key?

Need a key for your 2017 Nissan Versa? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.