2019 Nissan Rogue Key Replacement

2019 Rogue key specs

Most second-generation Rogues use an Intelligent Key with push-button start, catalogued under FCC ID KR5S180144106 in three-, four- and five-button versions, with a metal emergency key inside. Base trims keep a conventional ignition and a three-button folding flip key, catalogued as CWTWB1G767 for 2014-2020, or a key with an integrated remote, and Nissan's 2020 manual still lists them. If your 2014 or 2015 Rogue is the older-shaped Rogue Select, it uses first-generation S35 keys instead.

What's specific to the 2019 Rogue

The 2019 Nissan Rogue is the sixth of 7 model years in the Rogue T32 (second generation) (2014–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2019 Nissan Rogue is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2019 Rogue can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2019 Nissan Rogue

• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a Nissan Rogue, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your 2019 Rogue and which we don't.
• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2019 Rogue, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan Rogue T32 (second generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the Rogue

Nissan's immobilizer is called NATS, short for Nissan Anti-Theft System, and nearly every Nissan sold in the US since 2000 has one; a few early pickups and SUVs were built with plain keys. A chip in the key or fob has to answer the car before the engine is allowed to run, and a small security light on the dash blinks while the system is armed. Around 2000, cars such as the Maxima and Altima used the Texas Crypto 4D60 transponder. From about 2003, the 350Z, Armada, Frontier and later Altimas and Maximas moved to the Philips ID46, which stayed inside Nissan's Intelligent Key fobs for about a decade. Intelligent Key proximity fobs arrived first with a twist-knob ignition on Pathfinders, Armadas and the 2007 Maxima, and the 2007 Altima made push-button start standard. Some 2013-era fobs switched to Hitag 3 (ID47), and Hitag AES (4A) took over from the 2016 Maxima, the 2018 Leaf and Kicks, and the 2019 Altima. The newest platforms, including the Ariya, the 2025 Kicks and the 2025 Armada, use current-generation fobs and add security layers that make lost-key work slower. Your model year and the part number inside your fob tell us which system you have.

• Catalogs list this Rogue's Intelligent Key under FCC ID KR5S180144106, which differs from the KR5S180144014 used on the Murano and Pathfinder of the same years.
• A remote-start fob adds a button that only works on Rogues built with factory remote engine start.
• Supplier catalogs list 2014-2019 Rogue transponder keys with an AES chip, a newer type than the ID46 keys of earlier Nissans.
• Nissan's owner's manuals list a folding jackknife key as optional equipment on this generation through 2020, so a base Rogue may have no push button.

Programming a 2019 Rogue key

Both key types are registered through the OBD-II port with a PIN calculated from the body control module's code, and registration erases any key not present. Supplier notes warn that some 2015-2016 Rogue body control modules can be damaged during key programming, so we check the module before starting and use the safer procedure for it. Used fobs may be locked to their first car; a new or properly unlocked fob avoids that problem.

Spare keys are routine, but some 2015-2016 body control modules need extra care and later AES fobs can need extra steps or a dealer for all-keys-lost, which we check by VIN.

Lost every key to your Rogue?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Nissan Rogue can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Nissan Rogue requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Rogue and your schedule.

Rogue key battery

Battery details for the 2019 Rogue: CR2032 (jackknife key and later Intelligent Keys); CR2025 (2014-2015 Intelligent Keys); CR1620 (integrated key fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Rogue uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Nissan keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Rogue, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Rogue key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Nissan Rogue is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• Making one new key wipes every key that wasn't present for the registration. If an old spare suddenly stops starting the car after a key was added somewhere, that is usually why, and the spare has to be registered again.
• When a fob battery runs low on a push-button Nissan, the owner's manual procedure is to press the brake and touch the ignition button with the Intelligent Key. The car reads the chip at close range and starts even with weak remote range.
• High-mileage Altimas, Maximas and Frontiers from the 2000s often have worn ignition wafers and keys worn smooth. A key cut to factory code, rather than copied from the worn original, usually turns the ignition far more smoothly.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2019 Nissan Rogue key?

Need a key for your 2019 Nissan Rogue? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.