2022 Nissan Kicks Key Replacement

2022 Kicks key specs

First-generation Kicks fobs come in two common versions: a three-button fob with lock, unlock and panic, and a four-button fob that adds remote engine start on cars equipped for it. Both hide a mechanical emergency key for the driver's door. Supplier catalogs list newer part numbers from 2022, so the label inside your fob decides which one fits. Walk up with the fob and the request switch on the door handle locks or opens the car; the engine starts with the push-button ignition. The 2025 Kicks Play carries over this generation's design.

What's specific to the 2022 Kicks

The 2022 Nissan Kicks is the fifth of 7 model years in the Kicks P15 (first generation) (2018–2024), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2022 Nissan Kicks is about 4 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2022 Kicks can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2022 Nissan Kicks

• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Nissan Kicks P15 (first generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Nissan immobilizer works on the Kicks

Nissan's immobilizer is called NATS, short for Nissan Anti-Theft System, and nearly every Nissan sold in the US since 2000 has one; a few early pickups and SUVs were built with plain keys. A chip in the key or fob has to answer the car before the engine is allowed to run, and a small security light on the dash blinks while the system is armed. Around 2000, cars such as the Maxima and Altima used the Texas Crypto 4D60 transponder. From about 2003, the 350Z, Armada, Frontier and later Altimas and Maximas moved to the Philips ID46, which stayed inside Nissan's Intelligent Key fobs for about a decade. Intelligent Key proximity fobs arrived first with a twist-knob ignition on Pathfinders, Armadas and the 2007 Maxima, and the 2007 Altima made push-button start standard. Some 2013-era fobs switched to Hitag 3 (ID47), and Hitag AES (4A) took over from the 2016 Maxima, the 2018 Leaf and Kicks, and the 2019 Altima. The newest platforms, including the Ariya, the 2025 Kicks and the 2025 Armada, use current-generation fobs and add security layers that make lost-key work slower. Your model year and the part number inside your fob tell us which system you have.

• Catalogs list FCC ID KR5TXN1 for the three-button fob and KR5TXN3 for the remote-start version, both shared with Rogue models of the period.
• When the fob battery is low, pressing the brake and touching the fob to the ignition button still starts the car.

Programming a 2022 Kicks key

We register Kicks fobs through the OBD-II port after reading the body control module's code and calculating the PIN. Every fob you want to keep has to be present. Supplier listings say these fobs can be reused only after being unlocked or re-flashed, so a new fob is usually simpler. Spare keys are handled on site, and all-keys-lost usually is too, with the emergency key cut by decoding the driver's door lock.

Spare fobs are routine on this generation. Later cars with newer fobs may need extra steps or a dealer for all-keys-lost, which we confirm by VIN.

Lost every key to your Kicks?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Nissan Kicks can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2022 Nissan Kicks we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Kicks key battery

Most fobs for a 2022 Nissan Kicks open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Kicks uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Nissan Kicks keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Nissan system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Kicks key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Kicks came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Nissan system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Nissan key problems

• Making one new key wipes every key that wasn't present for the registration. If an old spare suddenly stops starting the car after a key was added somewhere, that is usually why, and the spare has to be registered again.
• When a fob battery runs low on a push-button Nissan, the owner's manual procedure is to press the brake and touch the ignition button with the Intelligent Key. The car reads the chip at close range and starts even with weak remote range.
• Secondhand Intelligent Keys are a common dead end. Many newer Hitag AES fobs lock to the first car that learns them, and a fob with a different FCC ID or part number won't register even when it looks identical to yours.

Tips from a mobile locksmith

• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2022 Nissan Kicks key?

Don't wait until the last key disappears. If your Nissan Kicks is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.