2016 Mercedes-Benz Sprinter Key Replacement

2016 Sprinter key specs

Mercedes-Benz Sprinters from 2010 to 2018 use a remote head key: remote buttons on a plastic head, a transponder inside, and an HU64 two-track blade that turns the ignition. Cargo, crew, passenger and cab-chassis vans share the key, and so do the Freightliner Sprinters of these years. Fleets should keep two keys per van, since adding a key from a working one is much simpler than replacing the last. If the buttons quit but the van still starts, the remote battery is the first suspect.

What's specific to the 2016 Sprinter

The 2016 Mercedes-Benz Sprinter is the seventh of 9 model years in the Sprinter NCV3 (W906) (2010–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 10 years old, a 2016 Mercedes-Benz Sprinter has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

If a newly cut key turns the 2016 Sprinter's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2016 Mercedes-Benz Sprinter

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2016 Sprinter, we open the old key and show you what's broken before recommending anything.
• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Mercedes-Benz Sprinter, we'll explain which method fits and why.

How the Mercedes-Benz immobilizer works on the Sprinter

Mercedes-Benz calls its immobilizer the Drive Authorization System, and for key work it helps to sort the cars into three eras. The oldest models we cover, such as the 2000-2002 E-Class, the last W202 C-Class and the first CLK, use a key with remote buttons in its head and an HU64 two-track blade that turns a conventional ignition lock while the immobilizer checks electronics inside the key. The next era, known in the trade as FBS3 or DAS 3, came to the US on the S-Class and CL around 2000 and spread to nearly every model within a few years. Its key is a fob that plugs into an electronic ignition switch and identifies itself by infrared: chrome-bodied at first, then the familiar black fob with chrome sides. Keyless-Go let many of these cars open and start with the fob left in a pocket. Around 2014 and 2015, Mercedes began moving models to FBS4, and push-button start gradually became standard. FBS4 keys are produced by Mercedes-Benz for one VIN, which is why most newer cars mean a dealer order.

• Freightliner also sold NCV3 Sprinters through 2018, so match a key to the van's VIN rather than its badge.
• NCV3 keys use the Mercedes HU64 two-track blade.
• North America received this NCV3 van for 2007 as a Dodge and Freightliner, and it wore a Mercedes-Benz badge in the US from 2010.

Programming a 2016 Sprinter key

NCV3 keys are written to the van's electronic ignition switch with equipment that supports Mercedes vans. With a working key, we read the switch over OBD-II, prepare a new transponder key, cut the HU64 blade, and test locks and start. With every key lost, the switch often has to be removed and read on the bench, and some vans end up needing a dealer key by VIN. We confirm which case applies before quoting.

Spare keys are usually doable; all-keys-lost can need ignition-switch bench work or a dealer key, confirmed by VIN.

Lost every key to your Sprinter?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Mercedes-Benz Sprinter can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Mercedes-Benz Sprinter requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Sprinter and your schedule.

Sprinter key battery

If a new replacement doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Sprinter uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Mercedes-Benz system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a Sprinter key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Mercedes-Benz Sprinter is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mercedes-Benz key problems

• Keyless-Go cars can be targeted by relay thieves who pass the fob's signal from inside a house to the car. Many newer fobs switch off their keyless function after two quick presses of the lock button, and a signal-blocking pouch helps too.
• The electronic steering lock is a known weak point on the W204 C-Class and the W212 and W207 E-Class. When it fails, the key goes in but won't turn and the dash stays dark, and a new key will not fix it.
• Inland Empire summer heat shortens coin-cell life and is hard on fobs left on a sunny dashboard. If a Mercedes key starts responding only at close range, a new battery is the simplest first step.

Tips from a mobile locksmith

• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2016 Mercedes-Benz Sprinter key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Sprinter in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.