2019 Mercedes-Benz SLK / SLC Key Replacement

2019 SLK / SLC key specs

The R172 was sold as the SLK through 2016 and as the SLC from 2017 to 2020, in SLK250, SLK300, SLK350, SLC300, SLK55 AMG and AMG SLC 43 form. Most cars insert the fob into a dash ignition switch and turn it, while Keyless-Go cars use a removable start button in the same slot. Mercedes moved this car from FBS3 to FBS4 keys partway through production, and the fobs look almost the same, so we read the VIN before saying whether a spare can be made locally.

What's specific to the 2019 SLK / SLC

The 2019 Mercedes-Benz SLK / SLC is the eighth of 9 model years in the SLK / SLC R172 (SLK, then SLC) (2012–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2019 Mercedes-Benz SLK / SLC is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2019 Mercedes-Benz SLK / SLC

• Remote head key. Remote-head keys look similar across many vehicles, but the electronics inside are not interchangeable. Getting the right one for a Mercedes-Benz SLK / SLC means matching the FCC ID and part number printed on the back or inside the case, the operating frequency, which is commonly 315 MHz on US-market cars, the transponder type, and the button layout. A trim with remote start or a power liftgate may use a four- or five-button version where a base trim uses three. We check those details against your VIN and your existing key, if you have one, before cutting the blade. A wrong match can look perfect and still refuse to program.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2019 Mercedes-Benz SLK / SLC open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Mercedes-Benz immobilizer works on the SLK / SLC

Mercedes-Benz calls its immobilizer the Drive Authorization System, and for key work it helps to sort the cars into three eras. The oldest models we cover, such as the 2000-2002 E-Class, the last W202 C-Class and the first CLK, use a key with remote buttons in its head and an HU64 two-track blade that turns a conventional ignition lock while the immobilizer checks electronics inside the key. The next era, known in the trade as FBS3 or DAS 3, came to the US on the S-Class and CL around 2000 and spread to nearly every model within a few years. Its key is a fob that plugs into an electronic ignition switch and identifies itself by infrared: chrome-bodied at first, then the familiar black fob with chrome sides. Keyless-Go let many of these cars open and start with the fob left in a pocket. Around 2014 and 2015, Mercedes began moving models to FBS4, and push-button start gradually became standard. FBS4 keys are produced by Mercedes-Benz for one VIN, which is why most newer cars mean a dealer order.

• The SLC name arrived with the 2017 facelift, and SLC and late SLK cars belong to the same R172 generation.
• FBS4 keys are built for a single VIN by Mercedes-Benz and can't be made from a used fob.
• The 2020 model year was the last for the SLC in the US.

Programming a 2019 SLK / SLC key

An FBS3 car can usually get a spare from us: we read the ignition switch, calculate the key password using a working fob, and write a new key, with all-keys-lost possible on many cars once the switch is on the bench. FBS4 cars need a key built by Mercedes-Benz for the VIN and ordered through a dealer, which we don't originate. We confirm the system by VIN, then handle what's ours, including lockouts and emergency keys.

FBS3 builds can usually get spare keys from us; FBS4 builds need a dealer-ordered key, confirmed by VIN.

Lost every key to your SLK / SLC?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your SLK / SLC and your schedule.

SLK / SLC key battery

If a new replacement doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your SLK / SLC uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your SLK / SLC, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an SLK / SLC key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Mercedes-Benz SLK / SLC is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mercedes-Benz key problems

• The electronic steering lock is a known weak point on the W204 C-Class and the W212 and W207 E-Class. When it fails, the key goes in but won't turn and the dash stays dark, and a new key will not fix it.
• Mercedes keys are written to one car, so a secondhand fob bought online usually can't be programmed to yours. New keys made for your car, or keys ordered by VIN through a dealer, are the options that work.
• Inland Empire summer heat shortens coin-cell life and is hard on fobs left on a sunny dashboard. If a Mercedes key starts responding only at close range, a new battery is the simplest first step.

Tips from a mobile locksmith

• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2019 Mercedes-Benz SLK / SLC key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your SLK / SLC in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.