2019 Mercedes-Benz GL / GLS Key Replacement

2019 GL / GLS key specs

The second generation was sold as the GL from 2013 to 2016 and as the GLS from 2017 to 2019, and Mercedes changed its key system along the way. Earlier trucks use the FBS3 smart key that plugs into the ignition switch on the dash, and later ones moved to the FBS4 system with a fob that looks almost identical. Keyless-Go was available, letting the driver open the doors at the handle and start the engine with a removable button in the ignition slot. Because the two systems are handled so differently, the VIN tells us more than the badge does.

What's specific to the 2019 GL / GLS

2019 was the final model year of the GL / GLS X166 (2nd generation, GL then GLS), before the X167 (3rd generation GLS) arrived for 2020. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2019 Mercedes-Benz GL / GLS matches a 2013.

A 2019 Mercedes-Benz GL / GLS is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2019 Mercedes-Benz GL / GLS

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2019 Mercedes-Benz GL / GLS with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2019 Mercedes-Benz GL / GLS open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Mercedes-Benz immobilizer works on the GL / GLS

Mercedes-Benz calls its immobilizer the Drive Authorization System, and for key work it helps to sort the cars into three eras. The oldest models we cover, such as the 2000-2002 E-Class, the last W202 C-Class and the first CLK, use a key with remote buttons in its head and an HU64 two-track blade that turns a conventional ignition lock while the immobilizer checks electronics inside the key. The next era, known in the trade as FBS3 or DAS 3, came to the US on the S-Class and CL around 2000 and spread to nearly every model within a few years. Its key is a fob that plugs into an electronic ignition switch and identifies itself by infrared: chrome-bodied at first, then the familiar black fob with chrome sides. Keyless-Go let many of these cars open and start with the fob left in a pocket. Around 2014 and 2015, Mercedes began moving models to FBS4, and push-button start gradually became standard. FBS4 keys are produced by Mercedes-Benz for one VIN, which is why most newer cars mean a dealer order.

• The GL became the GLS with the 2017 facelift, so a 2016 GL and a 2017 GLS belong to the same X166 generation.
• FBS4 keys are built for a single vehicle and cannot be recoded, so a used fob from another GL or GLS will not work in yours.
• A Mercedes dealer can block a lost key so it no longer starts the truck.

Programming a 2019 GL / GLS key

On FBS3 trucks, we read the ignition switch through the OBD-II port, calculate the key password with help from a working fob, and write a new key; all-keys-lost usually means removing the switch for bench reading. FBS4 trucks work differently. Their keys are produced by Mercedes-Benz for one VIN and ordered through a dealer after ownership is verified, and we don't originate them. We can still open the truck, test the fob battery and emergency key, and help you prepare the paperwork for the order.

Earlier FBS3 trucks can usually get spare keys from us; FBS4 builds need a dealer-ordered key, which we confirm by VIN.

Lost every key to your GL / GLS?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Mercedes-Benz GL / GLS, ask us directly and you'll get a plain answer.

GL / GLS key battery

If a new replacement doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your GL / GLS uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Mercedes-Benz GL / GLS keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Mercedes-Benz system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a GL / GLS key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Mercedes-Benz GL / GLS is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Mercedes-Benz system adds equipment time and labor to the job.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mercedes-Benz key problems

• A weak 12-volt battery can make a Mercedes act as if it has a key problem: the fob isn't recognized, the ignition won't turn, or the doors won't respond. Checking voltage first can save an unnecessary key order.
• On dash-slot Mercedes models from the mid-2000s to the mid-2010s, a key that slides in but won't turn often points to a worn electronic ignition switch or a weak car battery rather than a bad key. We test both before replacing anything.
• Mercedes keys are written to one car, so a secondhand fob bought online usually can't be programmed to yours. New keys made for your car, or keys ordered by VIN through a dealer, are the options that work.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2019 Mercedes-Benz GL / GLS key?

Need a key for your 2019 Mercedes-Benz GL / GLS? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.