2010 Lincoln MKZ Key Replacement

2010 MKZ key specs

First-generation MKZs use a remote-head key with lock, unlock, trunk and panic buttons built into the key head. Catalogs list 2007-2010 cars under FCC ID OUCD6000022, a 315 MHz Texas 4D63 80-bit key sold as Ford part 164-R7040, and 2011-2012 cars under the CWTWB1U793 key also used on the Edge and F-150. The blade is the Ford 8-cut H75 profile throughout. The 2010 refresh changed the styling and interior but kept a conventional ignition and the same style of key.

What's specific to the 2010 MKZ

The 2010 Lincoln MKZ is the fourth of 6 model years in the MKZ First generation (CD3) (2007–2012), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2010 Lincoln MKZ is about 16 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2010 Lincoln MKZ

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2010 MKZ, we open the old key and show you what's broken before recommending anything.
• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Lincoln MKZ only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.

How the Lincoln immobilizer works on the MKZ

Every Lincoln from the 2000 model year on uses Ford's Passive Anti-Theft System, PATS, which Ford also markets as SecuriLock. A transponder in the key head, or inside the fob on push-button cars, answers a challenge from the car, and the engine won't run unless that code matches a key stored in memory. The hardware changed in clear steps. The Town Car, Continental and Navigator through 2002, plus the 2002 Blackwood, use a Texas 4C fixed-code chip in a Ford 8-cut key. The 2000-2002 LS used a Texas 4D60 chip, and from 2003 the line moved to Texas 4D63 keys. Remote-head keys, with the lock buttons molded into the key, show up from the 2006 Zephyr on. Intelligent Access with push-button start arrived on the 2009 MKS, using 315 MHz fobs with a Philips ID46 chip and a hidden emergency blade. The 2013 MKZ introduced 902 MHz fobs with NXP Hitag Pro encryption and an HU101 emergency blade, while the MKX, MKS, MKT and Navigator kept the older 315 MHz style for several more years. The 2020 Aviator and Corsair added Phone As A Key, which lets a paired smartphone act as the key.

• Catalogs list the OUCD6000022 remote-head key for the Zephyr and for 2007-2010 MKZs, so one key style covers all four of those years.
• Strattec 5913437 is the H92-PT 80-bit 4D63 transponder key that catalogs list for Lincoln models from 2003 through 2013, which makes a plain ignition-only spare easy to source.

Programming a 2010 MKZ key

New keys are programmed through the OBD-II port after PATS security access, and many cars also accept Ford's two-key on-board routine. Remote buttons pair separately, usually through an ignition-cycling sequence. A plain transponder key can serve as a low-cost ignition spare. For all-keys-lost, we cut a key to code or decode a lock, erase the old keys and program two new ones.

Lost every key to your MKZ?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Lincoln MKZ can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your MKZ and your schedule.

MKZ key battery

Most fobs for a 2010 Lincoln MKZ open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your MKZ uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Lincoln system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an MKZ key

• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Lincoln system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Lincoln key problems

• After a key erase, PATS expects at least two programmed keys, and a car left with one may store code B1213. Ford's owner add-key routine also needs two working keys, so a one-key Lincoln is worth fixing early.
• Remote-head keys from roughly 2006 to 2014 crack at the blade root or wear through the button pads. The transponder and remote board can often move into a new shell, but the new blade still has to be cut to your car.
• Town Cars spent years in livery service, so plenty of them have very high mileage, along with worn keys and ignition cylinders. Cutting a fresh key to code, rather than copying a worn one, usually restores a smooth turn.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2010 Lincoln MKZ key?

Need a key for your 2010 Lincoln MKZ? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.