2021 Infiniti Q60 Key Replacement

2021 Q60 key specs

The second-generation Q60 shares its smart keys with the Q50 of the same years. 2017-2018 coupes use FCC ID KR5S180144204 (part 285E3-4HB0C, four buttons) or a five-button remote-start fob under KR5S180144014 (285E3-4HK0A). From 2020, coupes use KR5TXN7 fobs, four-button 285E3-6HE1A or five-button 285E3-6HE6A. All take a CR2032 and carry a hidden emergency blade. 2019 cars fall between the two families, so check the label on your original.

What's specific to the 2021 Q60

The 2021 Infiniti Q60 is the fifth of 6 model years in the Q60 CV37 (2nd generation) (2017–2022), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2021 Infiniti Q60 is about 5 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2021 Q60 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2021 Infiniti Q60

• Smart proximity key (push-to-start). A smart or proximity key lets a 2021 Infiniti Q60 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Infiniti immobilizer works on the Q60

• The 2017-2022 Q60 uses different fobs from the 2014-2015 Q60, so the older JK65A fob will not work on these cars.
• Infiniti ended Q60 production with the 2022 model year.

Programming a 2021 Q60 key

Programming is OBD-II based: the programmer derives the PIN from the body control module, then registers each fob, dropping any that are not present. Spare fobs are routine. With all keys lost the job depends on build date and tool coverage, so we confirm by VIN first; when it is doable we open the coupe, cut the emergency blade by code and register new fobs on site.

Spare fobs are routine; all-keys-lost on these encrypted-fob cars can need extra procedures or a dealer PIN, which we confirm by VIN before quoting.

Lost every key to your Q60?

Losing every key to an Infiniti is often fixable on site without a tow, depending on the model. We verify ownership first, with your ID plus the registration or title, and then open the car without damage. The mechanical blade is cut by key code or decoded from a door lock; most Infinitis from 2000 into the 2020s use the same NSN14-style edge-cut profile (Ilco DA34), with a few older exceptions. On turn-key models that blade gets a transponder head and is programmed over OBD-II. On Intelligent Key models we register new fobs to the car and cut the emergency blade that hides inside each one. Several models are marked limited here because all-keys-lost can need extra procedures or a dealer PIN, and the QX30's Mercedes-based system is a dealer job. We tell you which case applies before any work starts.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Infiniti Q60, ask us directly and you'll get a plain answer.

Q60 key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Q60 uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Infiniti Q60 keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Infiniti system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Q60 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Q60 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Infiniti key problems

• A flashing security light with a key that looks fine usually points to a cracked transponder, a fob with a damaged chip, or an aftermarket remote-start bypass module interfering with the immobilizer.
• A dead 12-volt battery can leave you outside a push-button Infiniti even with a good fob. The mechanical key hidden inside the fob opens the driver's door so you can reach the hood release.
• Secondhand fobs bought online often fail. Newer smart keys lock to their first vehicle and must be unlocked, and a fob with the wrong FCC ID, IC number or part number will not register no matter how similar it looks.
• On older turn-key models like the I35, G35 and QX4, worn keys and ignition wafers cause sticking or no-turn ignitions. Cutting a fresh key by code, rather than copying a worn one, often solves it.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2021 Infiniti Q60 key?

Don't wait until the last key disappears. If your Infiniti Q60 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.