2019 Infiniti Q50 Key Replacement

2019 Q50 key specs

Every Q50 has an Intelligent Key with push-button start, but the fob changed during these years. 2014-2015 cars use FCC ID KR5S180144203 (four buttons, part 285E3-4HD0C, 315 MHz). From 2016 the common fob is KR5S180144204 (285E3-4HB0C, 433 MHz), and a five-button remote-start fob under KR5S180144014 (285E3-4HK0A) is listed for 2016-2018. The 2016 model year can carry any of three fobs, so read the label on yours. All take a CR2032 and hide an emergency blade.

What's specific to the 2019 Q50

2019 was the final model year of the Q50 V37, before the V37 arrived for 2020. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2019 Infiniti Q50 matches a 2014. A 2019 Infiniti Q50 is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2019 Q50 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2019 Infiniti Q50

• Smart proximity key (push-to-start). A smart or proximity key lets a 2019 Infiniti Q50 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Infiniti immobilizer works on the Q50

Nearly every Infiniti sold in the US since 2000 has an engine immobilizer built on Nissan's NATS (Nissan Anti-Theft System). A transponder in the key or fob has to answer the car's challenge before the engine is allowed to run, and the small security light on the dash blinks while the system is armed. The chip inside changed over the years. The 1997-2001 Q45 used a fixed-code Texas 4C transponder, while the G20, I30, I35 and QX4 used the Texas Crypto 4D60. From 2003 the G35, FX and later models moved to the Philips ID46, which stayed in the Intelligent Key fobs of many models well into the 2010s. Infiniti's Intelligent Key lets the car recognize a fob in your pocket; some early cars such as the FX paired it with a turning ignition knob, and push-button start became standard on most models by about 2009. From roughly 2013 the newer fobs use different electronics, and a replacement has to match both the FCC ID and the IC number printed on the original. The QX30 is the outlier: its key system came from Mercedes-Benz.

• 2014-2015 Q50 fobs operate at 315 MHz while 2016-2019 fobs operate at 433 MHz, one reason they are not interchangeable.
• The 2016 Q50 has three possible fobs with different FCC IDs, so the VIN is the safest way to confirm the part.
• Used fobs of this generation can be reused only after they have been unlocked.

Programming a 2019 Q50 key

Q50 fobs are registered through the OBD-II port after the programmer reads the PIN from the body control module, and any fob not presented in that session is erased. Spare fobs are routine. All-keys-lost on these encrypted-fob cars depends on the build and tool coverage, so we confirm the exact fob from your VIN first, because the 2014-2015 and 2016-2019 fobs are different parts. When it is doable we cut the blade by code and register new fobs on site.

Spare fobs are routine; all-keys-lost on these encrypted-fob cars can need extra procedures or a dealer PIN, which we confirm by VIN before quoting.

Lost every key to your Q50?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Q50 and your schedule.

Q50 key battery

Most fobs for a 2019 Infiniti Q50 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Q50 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Infiniti system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Q50 key

• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Infiniti system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Infiniti key problems

• A flashing security light with a key that looks fine usually points to a cracked transponder, a fob with a damaged chip, or an aftermarket remote-start bypass module interfering with the immobilizer.
• On older turn-key models like the I35, G35 and QX4, worn keys and ignition wafers cause sticking or no-turn ignitions. Cutting a fresh key by code, rather than copying a worn one, often solves it.
• Secondhand fobs bought online often fail. Newer smart keys lock to their first vehicle and must be unlocked, and a fob with the wrong FCC ID, IC number or part number will not register no matter how similar it looks.

Tips from a mobile locksmith

• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2019 Infiniti Q50 key?

Don't wait until the last key disappears. If your Infiniti Q50 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.