2001 Infiniti G20 Key Replacement

2001 G20 key specs

Every 2000-2002 G20 starts with a plain-head transponder key; there was no remote-head or smart key option. Locks and trunk release are handled by a separate keyless-entry fob, which can be replaced independently of the ignition key. Aftermarket transponder keys for this car are sold as NI01T or NI02T blanks with a 4D60 chip, and a copy needs both the correct cut and a registered chip to start the engine. A key that turns but will not start usually means the chip was never programmed.

What's specific to the 2001 G20

The 2001 Infiniti G20 is the second of 3 model years in the G20 P11 (2nd generation) (2000–2002), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2001 Infiniti G20 is about 25 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2001 Infiniti G20

• Transponder (chip) key. A transponder key carries a small chip in its head, usually a glass capsule or a carbon wafer, with no battery of its own. When you turn the key in a 2001 Infiniti G20 that uses one, an antenna ring around the ignition energizes the chip and asks for its code. If the answer matches what the immobilizer has stored, the engine is allowed to run. If it doesn't, you get the classic symptoms: the engine cranks but won't fire, or it fires and dies after a second, and the security light on the dash flashes or stays lit. That's why a perfectly cut copy without a programmed chip will open the doors but won't start the car.
• Key with separate remote fob. Pairing a separate remote to a 2001 Infiniti G20 is a different job from programming the ignition key. Some vehicles accept new remotes through an on-board sequence of key turns and button presses; others need a scan tool connected to the OBD-II port. On many of them, entering remote programming mode clears every remote the car already knows, so any remote you want to keep has to be present and re-paired during the same session. Before we start, gather every remote that belongs to the vehicle. Leaving one in a kitchen drawer is a classic way to end up with a remote that quits the day after a new one is added.

How the Infiniti immobilizer works on the G20

Nearly every Infiniti sold in the US since 2000 has an engine immobilizer built on Nissan's NATS (Nissan Anti-Theft System). A transponder in the key or fob has to answer the car's challenge before the engine is allowed to run, and the small security light on the dash blinks while the system is armed. The chip inside changed over the years. The 1997-2001 Q45 used a fixed-code Texas 4C transponder, while the G20, I30, I35 and QX4 used the Texas Crypto 4D60. From 2003 the G35, FX and later models moved to the Philips ID46, which stayed in the Intelligent Key fobs of many models well into the 2010s. Infiniti's Intelligent Key lets the car recognize a fob in your pocket; some early cars such as the FX paired it with a turning ignition knob, and push-button start became standard on most models by about 2009. From roughly 2013 the newer fobs use different electronics, and a replacement has to match both the FCC ID and the IC number printed on the original. The QX30 is the outlier: its key system came from Mercedes-Benz.

• The G20's NATS immobilizer looks for a Texas Crypto 4D60 transponder in the key head.
• Keyless entry on the 2000-2002 G20 comes from a separate remote, so a key-only job never requires a new fob.
• The blade uses the NSN14 edge-cut profile found on most Infiniti keys of the next two decades.

Programming a 2001 G20 key

We cut the blade by code or from your existing key, then register the 4D60 chip over the OBD-II port using the NATS PIN that our programmer reads from the car. Registration re-learns the full key set, so any working key you want to keep should be on hand. With all keys lost, the blade is cut by key code or decoded from a door lock and programmed the same way, on site.

Lost every key to your G20?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your G20 and your schedule.

G20 key battery

Most fobs for a 2001 Infiniti G20 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh replacement, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your G20 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Infiniti system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a G20 key

• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Infiniti key problems

• On older turn-key models like the I35, G35 and QX4, worn keys and ignition wafers cause sticking or no-turn ignitions. Cutting a fresh key by code, rather than copying a worn one, often solves it.
• Weak fob batteries are the most common cause of a key-not-detected warning on push-button Infinitis. Most fobs take a CR2032 or CR2025 coin cell, and a fresh battery often clears the warning without any reprogramming.
• A dead 12-volt battery can leave you outside a push-button Infiniti even with a good fob. The mechanical key hidden inside the fob opens the driver's door so you can reach the hood release.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2001 Infiniti G20 key?

The quickest route to a working key for a 2001 Infiniti G20 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.