2017 Hyundai Accent Key Replacement

2017 Accent key specs

Accents from 2012 through 2017, sedan and five-door hatchback alike, start with a conventional key and a separate three-button remote. Supplier listings say the remote is for turn-key cars with standard keyless entry, and note that Canadian-market cars use a chipped key that may not work on US cars. The remote changed partway through the run: early cars use FCC ID TQ8-RKE-3F01 (part 95430-1R200, 315 MHz) and later cars use TQ8-RKE-4F14 (95430-1R300, 434 MHz), and 2014 cars can have either. Both remotes run on a CR2032 battery.

What's specific to the 2017 Accent

2017 was the final model year of the Accent RB (fourth generation), before the HC (fifth generation) arrived for 2018. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2017 Hyundai Accent matches a 2012.

At roughly 9 years old, a 2017 Hyundai Accent has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2017 Hyundai Accent

• Basic mechanical key. A plain mechanical key has no chip and no electronics, just a cut blade that lines up the wafers inside the lock. If your 2017 Hyundai Accent uses one, replacement is mostly a cutting job, but how it's cut matters. Copying a worn key copies its wear, and a duplicate of a duplicate drifts further from spec each time. We prefer to cut by code: we look up or decode the factory bitting, then cut a fresh key to the original depths on a code machine. The result turns smoothly in the doors and ignition instead of needing a jiggle. If the ignition wafers themselves are already worn, we'll point that out too.
• Key with separate remote fob. Some Hyundai Accent owners carry two pieces: a transponder key for the ignition and a separate remote fob on the same ring. Because they work independently, you only have to replace what's actually missing or broken. A lost remote still leaves you with a key that opens the doors and starts the engine, so it's an inconvenience rather than an emergency. A lost key is the more urgent half, since it has to be cut and its chip programmed before the car will run. We stock and program both sides, and if the whole ring is gone, we handle the key first and then pair a new remote.

How Accent keys work on this generation

• Early and late remotes for this Accent carry different FCC IDs, TQ8-RKE-3F01 and TQ8-RKE-4F14, and the wrong one won't pair.
• Canadian-market Accents of these years have a transponder in the key, which is why some online listings show a chipped key.

Cutting a 2017 Accent key

A spare key is cut from your key or from the VIN key code, and US cars need no transponder registration unless yours turns out to carry a chip, which we check first. When every key is lost, we decode the door lock or cut by code. The separate remote is paired through the diagnostic port with a scan tool, and we program all of your remotes in one visit, since pairing typically overwrites the stored list.

How we program a Hyundai depends on which group it falls into. Turn-key cars without an immobilizer need no key programming at all: we cut the blade by code or by decoding a lock, then pair the remote, which on most models takes a scan tool or a diagnostic-connector routine rather than a button sequence. Transponder and smart-key Hyundais are programmed through the OBD-II port, and the car won't enter key-learning mode until the tool supplies the immobilizer PIN tied to the VIN. Registered locksmiths request that PIN through the NASTF Vehicle Security Professional registry. On most Hyundai systems, registration rewrites the whole key list, so bring every key you want to keep working. Smart fobs must be new or properly unlocked, and their hidden emergency blade is cut separately. The newest Hitag AES fobs need current tool software, and Digital Key phone credentials are set up by the owner in Hyundai's app, not by us.

Lost every key to your Accent?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Hyundai Accent can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2017 Hyundai Accent we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Accent key battery

Most fobs for a 2017 Hyundai Accent open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
2. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
3. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Accent key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2017 Hyundai Accent key?

Don't wait until the last key disappears. If your Hyundai Accent is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.