2006 Honda S2000 Key Replacement

2006 S2000 key specs

The 2004-2009 AP2 keeps the same arrangement: a transponder key turned to ON, then the red start button. Keyless entry still came from a separate four-button remote. The 2008-2009 CR (Club Racer) is part of this generation. As with the AP1, catalogs list more than one blank and chip type across these years, so we confirm from your key itself before cutting.

What's specific to the 2006 S2000

The 2006 Honda S2000 is the third of 6 model years in the S2000 AP2 (2004–2009), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2006 Honda S2000 is about 20 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2006 Honda S2000

• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Honda S2000, we'll explain which method fits and why.
• Key with separate remote fob. Some Honda S2000 owners carry two pieces: a transponder key for the ignition and a separate remote fob on the same ring. Because they work independently, you only have to replace what's actually missing or broken. A lost remote still leaves you with a key that opens the doors and starts the engine, so it's an inconvenience rather than an emergency. A lost key is the more urgent half, since it has to be cut and its chip programmed before the car will run. We stock and program both sides, and if the whole ring is gone, we handle the key first and then pair a new remote.

How the Honda immobilizer works on the S2000

• AP2 cars have the 2.2-liter engine, but the key and start-button sequence carry over from the AP1.
• The 2008-2009 Club Racer uses the same key and start-button sequence as other AP2 cars.
• The 2009 model year was the S2000's last in the US.

Programming a 2006 S2000 key

With a working key, we add a spare through the OBD-II port or copy it where the chip allows, and cut the blade to code. For all-keys-lost, we confirm tool coverage for your year, decode a door lock, cut a key, and register it on site, then add a second key while we're there. Whichever remote your car uses, factory or dealer-installed, it is matched by FCC ID and paired separately.

Spares are usually simple. With all keys lost, we confirm tool coverage for your exact year first; some cases may need a Honda dealer.

Lost every key to your S2000?

Losing every key to a Honda built between 2000 and about 2021 is usually handled where the car sits. We decode the driver's door lock to cut a working blade, connect through the OBD-II port, register new keys, and erase the lost ones so they can no longer start the car. A 2000 Civic or a 2000-2001 CR-V has no transponder at all, so a correctly cut key is the whole job. Smart-key Hondas need a new fob plus a cut emergency blade. The newest systems, on the 2022-and-later Civic and the 2023-and-later Accord and CR-V, depend on current tool coverage, and some cases still have to go through a Honda dealer; we tell you which applies before any work starts. Expect to show ID and proof of ownership first.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Honda S2000 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2006 Honda S2000 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

S2000 key battery

Battery details for the 2006 S2000: CR2025 (separate remote). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your S2000 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your S2000, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an S2000 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your S2000 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Honda key problems

• Remote-head keys, used from the 2003 Accord onward, tend to fail at the plastic: the key-ring loop snaps, the head splits, or the blade works loose. The circuit board and transponder can usually be moved into a new shell instead of buying a whole key.
• If a Honda smart key battery dies, slide out the built-in key to open the driver's door. To start, press the brake and touch the H logo on the fob to the ENGINE START/STOP button while the button blinks.
• Honda has recalled some early-2000s models because a worn ignition interlock could let the key come out while the shifter was not in Park. If yours does that, check recall status by VIN at nhtsa.gov.
• High-mileage Hondas with laser-cut HON66 keys often develop worn ignition and door wafers, so the key must be jiggled to turn. A new key cut to factory code, not copied from the worn one, often turns cleanly; a badly worn cylinder needs repair.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2006 Honda S2000 key?

The quickest route to a working key for a 2006 Honda S2000 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.