2017 GMC Sierra 1500 Key Replacement

2017 Sierra 1500 key specs

The 2014-2018 Sierra 1500 introduced GM's HU100 laser-cut key, with a track milled into its face, carrying an extended Philips 46 chip. These trucks start with a turned key; push-button start did not reach the Sierra until the 2019 redesign. Keyless entry and remote start come from a separate fob with three to five buttons (FCC ID M3N32337100). The remote does not hold the transponder, so the key and remote are always separate parts on this truck, and losing one does not mean replacing both.

What's specific to the 2017 Sierra 1500

The 2017 GMC Sierra 1500 is the fourth of 5 model years in the Sierra 1500 K2XX (4th generation) (2014–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 9 years old, a 2017 GMC Sierra 1500 has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2017 GMC Sierra 1500

• Transponder (chip) key. A transponder key carries a small chip in its head, usually a glass capsule or a carbon wafer, with no battery of its own. When you turn the key in a 2017 GMC Sierra 1500 that uses one, an antenna ring around the ignition energizes the chip and asks for its code. If the answer matches what the immobilizer has stored, the engine is allowed to run. If it doesn't, you get the classic symptoms: the engine cranks but won't fire, or it fires and dies after a second, and the security light on the dash flashes or stays lit. That's why a perfectly cut copy without a programmed chip will open the doors but won't start the car.
• Key with separate remote fob. Separate remotes are easy to find online, which is exactly why they cause trouble. A listing can show the same shell as your GMC Sierra 1500 remote while hiding a different FCC ID, frequency or internal chip, and some used remotes are locked to the first vehicle they were paired with. We're glad to look at one you've already bought, and we'll tell you honestly whether it can be paired before charging you to try. If the remote side of your setup has become unreliable, it's also worth asking whether a fresh remote and a newly cut key, matched together, would cost less than chasing repairs on aging parts.

How the GMC immobilizer works on the Sierra 1500

• This generation moved the Sierra from the B111 Circle Plus key to the HU100 laser-cut profile.
• Keyless-entry remotes for 2014-2018 trucks use FCC ID M3N32337100 and a CR2032 battery.
• A key cut only mechanically will open the doors and crank the engine, but the truck will not run until its chip is programmed.

Programming a 2017 Sierra 1500 key

The HU100 blade is cut on a laser key machine by code or by decoding a lock. We then program the chip through the OBD-II port: with working keys the new one is added, and in an all-keys-lost situation the tool reads the security data and registers new keys while erasing the missing ones. The separate remote is programmed as its own step so remote start and the locks work.

How a GMC key gets programmed depends on its system. Passlock keys need no programming at all; if the theft-deterrent light comes on after a cylinder repair, GM's timed relearn (ignition on for roughly ten minutes, sometimes repeated three times) resets the module. Circle Plus and HU100 keys from 2007 to about 2021 are added through the OBD-II port with a key programmer that reads the security data, which skips any long relearn. Separate keyless-entry remotes are learned as their own step. Global B trucks and SUVs need a tool with an online connection, and some require a cable at the body control module. We decode your VIN first so you know which path applies before work starts.

Lost every key to your Sierra 1500?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your GMC Sierra 1500 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your GMC Sierra 1500, ask us directly and you'll get a plain answer.

Sierra 1500 key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Sierra 1500 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the GMC keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Sierra 1500, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Sierra 1500 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button GMC Sierra 1500 is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2017 GMC Sierra 1500 key?

The quickest route to a working key for a 2017 GMC Sierra 1500 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.