2013 Ford Taurus Key Replacement

2013 Taurus key specs

The 2013 refresh carried over the 80-bit remote-head key for turn-key cars, while Intelligent Access cars moved to a newer smart fob, FCC ID M3N5WY8609, which was also sold with a remote-start button. Intelligent Access was most common on Limited and SHO models, and many SE and SEL cars kept the turned key. Production ended in early 2019, so the 2019 model year is the last Taurus sold in the US.

What's specific to the 2013 Taurus

2013 was the first model year of the Taurus Sixth generation refresh. Early-production cars sometimes use different part numbers than later ones, so for a 2013 Ford Taurus we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. The key style carried over from the previous generation, but immobilizer data and part numbers can still differ, so a key from a 2012 is not a safe substitute.

At roughly 13 years old, a 2013 Ford Taurus has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit. If a newly cut key turns the 2013 Taurus's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2013 Ford Taurus

• Remote head key. Remote-head keys look similar across many vehicles, but the electronics inside are not interchangeable. Getting the right one for a Ford Taurus means matching the FCC ID and part number printed on the back or inside the case, the operating frequency, which is commonly 315 MHz on US-market cars, the transponder type, and the button layout. A trim with remote start or a power liftgate may use a four- or five-button version where a base trim uses three. We check those details against your VIN and your existing key, if you have one, before cutting the blade. A wrong match can look perfect and still refuse to program.
• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2013 Ford Taurus is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.
• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Ford Taurus only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.

How the Ford immobilizer works on the Taurus

Ford's immobilizer is PATS, the Passive Anti-Theft System, sold under the SecuriLock name. A transponder sealed in the key head, or built into the fob on push-button models, answers a coded challenge from a coil around the ignition or from antennas in the cabin, and the engine won't run until the powertrain computer accepts the answer. Across 2000-2026 the chip changed in clear steps. Pickups, big SUVs and the Crown Victoria used a fixed-code Texas 4C chip into the early 2000s, and the Excursion kept it through 2005. The first Escape and early Focus used a Texas 4D60. Between 2000 and 2004 most of the lineup moved to the encrypted Texas 4D63, with 80-bit versions becoming the norm around 2011, while most catalogs list the E-Series van with chip keys only from 2008. NXP Hitag Pro arrived with the 2013 Fusion, reached the F-150 for 2015 and now covers nearly the whole lineup. Remote-head keys appeared in the mid-2000s, Intelligent Access push-button fobs around 2010, and long-range 902 MHz fobs came with remote start. Recent models use 434 MHz fobs, and the Mustang Mach-E and F-150 Lightning added Phone As A Key.

• The M3N5WY8609 smart fob is shared with the 2013-2019 Flex and the 2011-2015 Explorer and Edge.
• The smart fob's emergency blade, Ford 164-R8041, carries no chip; it only opens the door.
• Catalogs list a five-button remote-head key with remote start, Ford 164-R8000, for 2012-2019 Tauruses.

Programming a 2013 Taurus key

Programming runs through the OBD-II port for both key styles. Owners with two working smart fobs can add a third on board, but a lost-key situation needs our programmer and the timed security access. We cut the emergency blade or the remote-head key on site. All-keys-lost is a single-visit job on most 2013-2015 cars, while later push-button cars can need an emulator or bypass cable first; either way we end with two working keys and the missing ones erased.

Spare keys are routine; all-keys-lost on 2016-and-later push-button Tauruses can need an emulator or bypass cable, which we confirm by VIN.

Lost every key to your Taurus?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Ford Taurus can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ford Taurus requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2013 Ford Taurus we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Taurus key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Taurus uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Ford Taurus keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ford keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ford system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a Taurus key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Ford Taurus is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Ford system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ford key problems

• MyKey, which spread across the lineup from about 2010, lets an admin key limit top speed and audio volume on another key. A newly programmed key carries no restrictions until you set MyKey up again in the vehicle menu.
• Two chip keys hanging side by side, or a metal gadget pressed against the key head, can confuse PATS. Ford's manuals warn about this, and a truck that starts once the extra keys come off the ring has a healthy key.
• A flashing theft light with a crank and no start, or an engine that fires and dies after a second, usually means PATS didn't read the key. A cracked head that lost its chip, or a hardware-store copy with no transponder, is the usual cause.

Tips from a mobile locksmith

• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2013 Ford Taurus key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Taurus in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.