2013 Ford Super Duty (F-250/F-350) Key Replacement

2013 Super Duty (F-250/F-350) key specs

The 2011 Super Duty, which introduced the 6.7-liter Power Stroke, moved to 80-bit 4D63 chips and remote-head keys: the common three-button key (Ford 164-R8070, FCC ID CWTWB1U793) and a four-button version for trucks with factory remote start. Plain 80-bit chip keys work as spares without remote buttons. Every truck in this generation uses a turned key, and push-button start didn't reach the Super Duty until 2017.

What's specific to the 2013 Super Duty (F-250/F-350)

The 2013 Ford Super Duty (F-250/F-350) is the third of 6 model years in the Super Duty (F-250/F-350) Third generation (2011–2016), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 13 years old, a 2013 Ford Super Duty (F-250/F-350) has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

If a newly cut key turns the 2013 Super Duty (F-250/F-350)'s ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2013 Ford Super Duty (F-250/F-350)

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2013 Ford Super Duty (F-250/F-350) with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Ford Super Duty (F-250/F-350) only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.

How the Ford immobilizer works on the Super Duty (F-250/F-350)

Ford's immobilizer is PATS, the Passive Anti-Theft System, sold under the SecuriLock name. A transponder sealed in the key head, or built into the fob on push-button models, answers a coded challenge from a coil around the ignition or from antennas in the cabin, and the engine won't run until the powertrain computer accepts the answer. Across 2000-2026 the chip changed in clear steps. Pickups, big SUVs and the Crown Victoria used a fixed-code Texas 4C chip into the early 2000s, and the Excursion kept it through 2005. The first Escape and early Focus used a Texas 4D60. Between 2000 and 2004 most of the lineup moved to the encrypted Texas 4D63, with 80-bit versions becoming the norm around 2011, while most catalogs list the E-Series van with chip keys only from 2008. NXP Hitag Pro arrived with the 2013 Fusion, reached the F-150 for 2015 and now covers nearly the whole lineup. Remote-head keys appeared in the mid-2000s, Intelligent Access push-button fobs around 2010, and long-range 902 MHz fobs came with remote start. Recent models use 434 MHz fobs, and the Mustang Mach-E and F-150 Lightning added Phone As A Key.

• The 164-R8070 key is shared with the 2011-2014 F-150, so replacements are widely stocked.
• A 40-bit key from a 2008-2010 Super Duty can't be programmed to these trucks.

Programming a 2013 Super Duty (F-250/F-350) key

We program the 80-bit chip through the OBD-II port after Ford's timed security access, and the remote-head key's buttons learn along with it. The two-key owner routine also works. For all-keys-lost, we decode a door lock or use the code, cut two keys, erase the old keys and program the new pair, so a key that left with a former driver no longer starts the truck.

Lost every key to your Super Duty (F-250/F-350)?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Ford Super Duty (F-250/F-350) can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Super Duty (F-250/F-350) and your schedule.

Super Duty (F-250/F-350) key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Super Duty (F-250/F-350) uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Ford Super Duty (F-250/F-350) keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ford keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ford system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Super Duty (F-250/F-350) key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Ford Super Duty (F-250/F-350) is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ford key problems

• MyKey, which spread across the lineup from about 2010, lets an admin key limit top speed and audio volume on another key. A newly programmed key carries no restrictions until you set MyKey up again in the vehicle menu.
• With only one programmed key, Ford's do-it-yourself spare routine is off the table because it needs two working keys. Adding a second key while the first still works is far simpler than an all-keys-lost visit later.
• Two chip keys hanging side by side, or a metal gadget pressed against the key head, can confuse PATS. Ford's manuals warn about this, and a truck that starts once the extra keys come off the ring has a healthy key.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2013 Ford Super Duty (F-250/F-350) key?

Need a key for your 2013 Ford Super Duty (F-250/F-350)? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.