2020 Ford F-150 Key Replacement

2020 F-150 key specs

The 2018 refresh kept the flip keys but brought Ford's slimmer smart fob, which takes a CR2450 cell. Catalogs list a three-button 315 MHz fob (Ford 164-R8163, FCC ID M3N-A2C93142300) and a five-button 902 MHz fob with remote start and tailgate buttons (Ford 164-R8166, FCC ID M3N-A2C93142600). XL and many XLT trucks still start with a turned key, using the three-button flip key or its four-button remote-start version. Catalogs list the same fobs for the 2019-2020 Raptor.

What's specific to the 2020 F-150

2020 was the final model year of the F-150 Thirteenth generation refresh, before the Fourteenth generation, P702 arrived for 2021. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2020 Ford F-150 matches a 2018. A 2020 Ford F-150 is about 6 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Smart-key cars like the 2020 F-150 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2020 Ford F-150

• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a Ford F-150, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your 2020 F-150 and which we don't.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Ford F-150 Thirteenth generation refresh, we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Ford immobilizer works on the F-150

• The 164-R8166 fob is shared with the 2017-2022 Super Duty, which keeps replacements easy to find.
• Catalogs list the same smart fobs for the 2019-2022 Raptor as for other F-150s of those years.

Programming a 2020 F-150 key

We program flip keys and fobs at the OBD-II port with a tool that covers Ford's Hitag Pro trucks, normally after a timed security access, then cut the blade or emergency insert to your locks. Adding a key with a working one present is routine. All-keys-lost on these trucks usually involves an emulator or bypass cable because of the active alarm; once it is connected, we erase the missing keys and program two.

Nearly all Ford key programming runs through the OBD-II port. On turn-key Fords from roughly 2000 to 2014, our programmer requests PATS security access, often a timed wait of about ten minutes, and then adds a key or erases and rebuilds the key list. If you already have two working keys, many of these vehicles also accept Ford's owner procedure, where each good key is switched on in turn, followed by the newly cut key. A fixed-code 4C key can simply be cloned. Most separate remotes from that era pair when the ignition is cycled eight times in quick succession, while integrated remote-head keys usually learn their buttons along with the chip. Hitag Pro flip keys and every push-button fob are registered with a programmer. On many 2015-and-later models an active alarm means an emulator or bypass cable for all-keys-lost work, and some 2020-and-later models add an online authorization step. We check your ID and registration or title before we start.

Spare keys are routine; all-keys-lost on these trucks generally needs an emulator or bypass cable, which we confirm by VIN first.

Lost every key to your F-150?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ford F-150 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2020 Ford F-150 we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

F-150 key battery

Battery details for the 2020 F-150: CR2032 (flip key); CR2450 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your F-150 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your F-150, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an F-150 key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2020 Ford F-150 key?

Don't wait until the last key disappears. If your Ford F-150 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.