2019 Fiat 500c Key Replacement

2019 500c key specs

Every 500c, from Pop and Lounge to the Abarth convertible, came with the same style of three-button flip key as the hatchback: lock, unlock and liftgate. The fob should show FCC ID LTQF12AM433TX or 2ADFTF12AM433TX, which pairs with the Delphi body computer. Remote heads from the Marelli-equipped 500L look nearly identical but won't operate a 500c's locks, so check the label before buying. If you only need something to start the car, a buttonless SIP22 key with an ID46 chip makes an inexpensive backup.

What's specific to the 2019 500c

2019 was the final model year of the 500c Type 312 cabriolet (Mexico-built). Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2019 Fiat 500c matches a 2012.

A 2019 Fiat 500c is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2019 Fiat 500c

• Flip (switchblade) key. A flip key folds its blade into the fob on a spring-loaded hinge and swings it out with the press of a button. Inside the body sit the transponder chip and the remote circuit board, which means the metal blade itself carries no electronics. That's good news when the blade snaps. On many flip keys for a Fiat 500c, we can cut a new blade to your key code and fit it into your existing fob, with no reprogramming required, because the chip and remote never left the housing. Many flip-key blades are laser-cut, with a groove milled along the side rather than notches on the edge, so they need a code machine built for that profile.
• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Fiat 500c, we'll explain which method fits and why.

How the Fiat immobilizer works on the 500c

Fiat returned to the US for the 2012 model year, and every Fiat sold here since has a transponder immobilizer that must recognize the key before the engine will keep running. The Mexican-built 500 and 500c use a Philips ID46 (Hitag 2) chip in a three-button flip key, paired with a Delphi-type body computer. The Serbian-built 500L uses the same chip family but a Magneti Marelli-type body computer, so its remote is not interchangeable with the 500's. The Italian-built 500X steps up to AES encryption: a Megamos AES chip in the early flip key and Hitag AES in the push-button smart key, which is the only style Fiat's owner's manuals describe from 2017 on. The 124 Spider is the outlier, built by Mazda in Hiroshima with a Mazda-designed smart key running at 315 MHz. The first-generation 500e shares the 500's turn-key setup, while the 2024 and newer 500e uses a newer Stellantis keyless system. On the 500, 500L and 500X, the mechanical blade is the SIP22 laser-cut profile. When the chip isn't recognized, the blade can still turn the ignition, but the immobilizer will not let the engine run.

• The 500c's fabric roof folds back on rails while the pillars and side frames stay fixed, so its doors and locks work like the hatchback's.
• Fiat's manual says that holding the fob's unlock button for at least three seconds opens the power top while the engine is off, so a worn unlock button affects more than the door locks.
• A soft top is never a safe entry point; a locked 500c is opened through the door with standard lockout tools.

Programming a 2019 500c key

The 500c programs exactly like the hatchback: an OBD-II connection, the security PIN, then the new transponder and remote are registered with the body computer. The convertible top has no separate key electronics, so nothing extra needs setting up afterward. If you're down to one key, adding a second one is a short visit. With no keys at all, we first decode the driver's door lock to cut a working SIP22 blade, then program it.

Lost every key to your 500c?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Fiat 500c requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2019 Fiat 500c we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

500c key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare CR2032 at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your 500c uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Fiat 500c keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Fiat system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a 500c key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Fiat 500c is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Fiat system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Fiat key problems

• Flip-key hinges on the 500 and 500L wear out over time. The blade stops locking open or swings loosely, often because the pivot pin has worked free. A new shell with the original circuit board moved over usually fixes it.
• On the push-button 500X, a weak smart-key battery can bring up a key-not-detected message. Fiat's manual says to touch the back of the fob, the side opposite the emergency key, to the START/STOP button, which usually gets you home.
• A key that turns but won't start the engine usually means the immobilizer doesn't recognize its transponder: a damaged chip, a key programmed to another car, or a spare that lost its pairing. Reprogramming fixes it; the ignition is rarely at fault.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2019 Fiat 500c key?

Need a key for your 2019 Fiat 500c? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.